參數資料
型號: AD9736BBCZRL
廠商: Analog Devices Inc
文件頁數: 39/72頁
文件大小: 0K
描述: IC DAC 14BIT 1.2GSPS 160CSPBGA
產品培訓模塊: Data Converter Fundamentals
DAC Architectures
標準包裝: 1,500
位數: 14
數據接口: 并聯
轉換器數目: 1
電壓電源: 模擬和數字
功率耗散(最大): 550mW
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 160-LFBGA,CSPBGA
供應商設備封裝: 160-CSPBGA(12x12)
包裝: 帶卷 (TR)
輸出數目和類型: 2 電流,單極
采樣率(每秒): 1.2G
AD9734/AD9735/AD9736
Rev. A | Page 44 of 72
DIGITAL BUILT-IN SELF TEST (BIST)
OVERVIEW
The AD973x includes an internal signature generator that
processes incoming data to create unique signatures. These
signatures are read back from the SPI port, allowing verification
of correct data transfer into the AD973x. BIST vectors provided
on the AD973x-EB evaluation board CD check the full width
data input or individual bits for PCB debug, utilizing the
procedure in the AD973X BIST Procedure section. Alterna-
tively, any vector can be used provided the expected signature is
calculated in advance.
The MATLAB routine, in the Generating Expected Signatures
section, calculates the expected signature. BIST verifies correct
data transfer because not all errors are always evident on a
spectrum analyzer. There are four BIST signature generators
that can be read back using Reg. 18 to Reg. 21, based on the
setting of the BIST selection bits (Reg. 17, Bits 7:6), as shown in
Table 24. The BIST signature returned from the AD973x
depends on the digital input during the test. Because the filters
in the DAC have memory, it is important to put the correct idle
value on the DATA input to flush the memory prior to reading
the BIST signature.
Placing the idle value on the data input also allows the BIST to
be set up while the DAC clock is running. The idle value should
be all 0s in unsigned mode (0x0000) and all 0s except for the
MSB in twos complement mode (0x2000).
The BIST consists of two stages; the first stage is after the LVDS
receiver and the second stage is after the FIFO. The first BIST
stage verifies correct sampling of the data from the LVDS bus
while the second BIST stage verifies correct synchronization
between the DAC_CLK domain and the DATACLK_IN
domain. The BIST vector is generated using 32-bit LFSR
signature logic. Because the internal architecture is a 2-bus
parallel system, there are two 32-bit LFSR signature logic blocks
on both the LVDS and SYNC blocks. Figure 84 shows where the
LVDS and SYNC phases are located.
Table 24. BIST Selection Bits
Bit
SEL<1>
SEL<0>
LVDS Phase 1
0
LVDS Phase 2
0
1
SYNC Phase 1
1
0
SYNC Phase 2
1
LVDS
RX
DB<13:0>
DATACLK_IN
SYNC LOGIC
FIFO
2x
D1
D2
DAC
LVDS
BIST
PH1
(RISE)
LVDS
BIST
PH2
(FALL)
SYNC
BIST
PH1
(RISE)
SYNC
BIST
PH2
(FALL)
SPI PORT
04862-082
Figure 84. Block Diagram Showing LVDS and SYNC Phase 1 and SYNC Phase 2
相關PDF資料
PDF描述
AD9778BSVZ IC DAC 14BIT DUAL 1GSPS 100TQFP
DAC8420ES-REEL IC DAC 12BIT QUAD SRL LP 16-SOIC
VE-B6W-MU-S CONVERTER MOD DC/DC 5.5V 200W
VE-B6V-MU-S CONVERTER MOD DC/DC 5.8V 200W
AD7834AN IC DAC 14BIT QUAD SRL 28-DIP
相關代理商/技術參數
參數描述
AD9736BBCZRL1 制造商:AD 制造商全稱:Analog Devices 功能描述:10-/12-/14-Bit, 1200 MSPS DACS
AD9736-DPG2-EBZ 功能描述:BOARD EVAL FOR AD9736 RoHS:是 類別:編程器,開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率(每秒):- 數據接口:串行,SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
AD9736-EB 制造商:Analog Devices 功能描述:14-BIT, 1.2 GSPS TXDAC+? D/A CONVERTER - Bulk
AD9736-EBZ 制造商:Analog Devices 功能描述:EVAL BD FOR AD9735 DAC, 10-/12-/14BIT, 1200 MSPS DACS - Bulk
AD9736XBC 制造商:Analog Devices 功能描述:14-BIT 1600 MSPS D/A CONVERTER - Bulk