- 您現在的位置：買賣IC網 > PDF目錄8995 > AD9748ACPZ (Analog Devices Inc)IC DAC 8BIT 210MSPS 32-LFCSP PDF資料下載
參數資料
| 型號： | AD9748ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8BIT 210MSPS 32-LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 1 |
| 系列： | TxDAC® |
| 設置時間： | 11ns |
| 位數： | 8 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 145mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 210M |
| 產品目錄頁面： | 785 (CN2011-ZH PDF) |
| 配用： | AD9748ACP-PCBZ-ND - BOARD EVAL FOR AD9748ACP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
Data Sheet
AD9748
Rev. B | Page 15 of 24
APPLYING THE AD9748
Output Configurations
The following sections illustrate some typical output
configurations for the AD9748. Unless otherwise noted, it is
assumed that IOUTFS is set to a nominal 20 mA. For applications
requiring the optimum dynamic performance, a differential
output configuration is suggested. A differential output
configuration can consist of either an RF transformer or a
differential op amp configuration. The transformer configuration
provides the optimum high frequency performance and is
recommended for any application that allows ac coupling. The
differential op amp configuration is suitable for applications
requiring dc coupling, bipolar output, signal gain, and/or
level shifting within the bandwidth of the chosen op amp.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage
results if IOUTA and/or IOUTB is connected to an appropriately
sized load resistor, RLOAD, referred to ACOM. This configuration
can be more suitable for a single-supply system requiring a dc-
coupled, ground referred output voltage. Alternatively, an
amplifier could be configured as an I-V converter, thus
converting IOUTA or IOUTB into a negative unipolar voltage.
This configuration provides the best dc linearity because
IOUTA or IOUTB is maintained at a virtual ground.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 25. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral
content lies within the transformer’s pass band. An RF transformer,
such as the Mini-Circuits T1–1T, provides excellent rejection of
common-mode distortion (that is, even-order harmonics) and
noise over a wide frequency range. It also provides electrical
isolation and the ability to deliver twice the power to the load.
Transformers with different impedance ratios can also be used
for impedance matching purposes. Note that the transformer
provides ac coupling only.
RLOAD
AD9748
MINI-CIRCUITS
T1-1T
OPTIONAL RDIFF
IOUTA
IOUTB
032
1
1-
022
Figure 25. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to ACOM to provide the necessary dc current path
for both IOUTA and IOUTB. The complementary voltages
appearing at IOUTA and IOUTB (that is, VOUTA and VOUTB)
swing symmetrically around ACOM and should be maintained
with the specified output compliance range of the AD9748. A
differential resistor, RDIFF, can be inserted in applications where
the output of the transformer is connected to the load, RLOAD,
via a passive reconstruction filter or cable. RDIFF is determined
by the transformer’s impedance ratio and provides the proper
source termination that results in a low VSWR. Note that
approximately half the signal power is dissipated across RDIFF.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS843001AGLFT | IC CLOCK GENERATOR 8-TSSOP |
| AD1934YSTZ | IC DAC 8CH W/ON-CHIP PLL 48LQFP |
| ICS840001AK-34LFT | IC FREQ SYNTHESIZER 16-VFQFPN |
| ICS84329BM-01LFT | IC SYNTHESIZER 700MHZ 28-SOIC |
| AD7303BRMZ | IC DAC 8BIT DUAL R-R 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9748ACPZ | 制造商:Analog Devices 功能描述:DAC, 8BIT, 210MSPS, LFCSP-32 |
| AD9748ACPZRL7 | 功能描述:IC DAC 8BIT 210MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD9748XCP | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 165 MSPS TxDAC D/A Converter |
| AD974AN | 功能描述:IC DAS 16BIT 4CH 200KSPS 28-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD974ANZ | 功能描述:IC DAS 16BIT 4CH 200KSPS 28DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。