- 您現在的位置：買賣IC網 > PDF目錄17065 > AD9750-EB (Analog Devices Inc)BOARD EVAL FOR AD9750 PDF資料下載
參數資料
| 型號： | AD9750-EB |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/22頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9750 |
| 產品培訓模塊： | DAC Architectures |
| 標準包裝： | 1 |
| 系列： | TxDAC® |
| DAC 的數量： | 1 |
| 位數： | 10 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 并聯 |
| 設置時間： | 35ns |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD9750 |
| 相關產品： | AD9750ARZ-ND - IC DAC 10BIT 125MSPS 28-SOIC AD9750ARUZ-ND - IC DAC 10BIT 125MSPS 28TSSOP AD9750ARUZRL7-ND - IC DAC 10BIT 125MSPS 28TSSOP AD9750ARZRL-ND - IC DAC 10BIT 125MSPS 28SOIC |
AD9750
–13–
REV. 0
POWER DISSIPATION
The power dissipation, PD, of the AD9750 is dependent on
several factors which include: (1) AVDD and DVDD, the
power supply voltages; (2) IOUTFS, the full-scale current output;
(3) fCLOCK, the update rate; (4) and the reconstructed digital
input waveform. The power dissipation is directly proportional
to the analog supply current, IAVDD, and the digital supply cur-
rent, IDVDD. IAVDD is directly proportional to IOUTFS as shown in
Figure 25 and is insensitive to fCLOCK.
Conversely, IDVDD is dependent on both the digital input wave-
form, fCLOCK, and digital supply DVDD. Figures 26 and 27
show IDVDD as a function of full-scale sine wave output ratios
(fOUT/fCLOCK) for various update rates with DVDD = 5 V and
DVDD = 3 V, respectively. Note, how IDVDD is reduced by more
than a factor of 2 when DVDD is reduced from 5 V to 3 V.
IOUTFS – mA
35
5
220
4
6
8
10
12
141618
30
25
20
15
10
I AVDD
–
mA
Figure 25. IAVDD vs. IOUTFS
RATIO (fCLOCK/fOUT)
18
16
0
0.01
1
0.1
I DVDD
–
mA
8
6
4
2
12
10
14
125MSPS
100MSPS
50MSPS
25MSPS
5MSPS
Figure 26. IDVDD vs. Ratio @ DVDD = 5 V
RATIO (fCLOCK/fOUT)
8
0
0.01
1
0.1
I DVDD
–
mA
6
4
2
125MSPS
100MSPS
50MSPS
25MSPS
5MSPS
Figure 27. IDVDD vs. Ratio @ DVDD = 3 V
APPLYING THE AD9750
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output configura-
tions for the AD9750. Unless otherwise noted, it is assumed
that IOUTFS is set to a nominal 20 mA. For applications requir-
ing the optimum dynamic performance, a differential output
configuration is suggested. A differential output configuration
may consist of either an RF transformer or a differential op amp
configuration. The transformer configuration provides the opti-
mum high frequency performance and is recommended for any
application allowing for ac coupling. The differential op amp
configuration is suitable for applications requiring dc coupling, a
bipolar output, signal gain and/or level shifting.
A single-ended output is suitable for applications requiring a
unipolar voltage output. A positive unipolar output voltage will
result if IOUTA and/or IOUTB is connected to an appropri-
ately sized load resistor, RLOAD, referred to ACOM. This con-
figuration may be more suitable for a single-supply system
requiring a dc coupled, ground referred output voltage. Alterna-
tively, an amplifier could be configured as an I-V converter thus
converting IOUTA or IOUTB into a negative unipolar voltage.
This configuration provides the best dc linearity since IOUTA
or IOUTB is maintained at a virtual ground. Note, IOUTA
provides slightly better performance than IOUTB.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion as shown in Figure 28. A
differentially coupled transformer output provides the optimum
distortion performance for output signals whose spectral content
lies within the transformer’s passband. An RF transformer such
as the Mini-Circuits T1-1T provides excellent rejection of
common-mode distortion (i.e., even-order harmonics) and noise
over a wide frequency range. It also provides electrical isolation
and the ability to deliver twice the power to the load. Trans-
formers with different impedance ratios may also be used for
impedance matching purposes. Note that the transformer
provides ac coupling only.
相關PDF資料 |
PDF描述 |
|---|---|
| UPS2E471MRD | CAP ALUM 470UF 250V 20% RADIAL |
| EVAL-AD5532HSEBZ | BOARD EVAL FOR AD5532HS |
| DC939A | BOARD DELTA SIGMA ADC LTC2484 |
| LGU2W680MELY | CAP ALUM 68UF 450V 20% SNAP |
| EVAL-AD5516-1EBZ | BOARD EVAL FOR AD5516-1 2.5V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9750-EBZ | 功能描述:BOARD EVAL FOR AD9750 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9751 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 300 MSPS High-Speed TxDAC+ D/A Converter |
| AD9751AST | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:10-BIT, 300 MSPS TXDAC+ D/A CONVERTER - Bulk 制造商:Analog Devices 功能描述:IC 10-BIT DAC |
| AD9751ASTRL | 制造商:Analog Devices 功能描述:DAC 1-CH Segment 10-bit 48-Pin LQFP T/R 制造商:Rochester Electronics LLC 功能描述:10-BIT, 300 MSPS TXDAC+ D/A CONVERTER - Tape and Reel |
| AD9751ASTZ | 功能描述:IC DAC 10BIT 300MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。