參數資料
型號： AD9883AKSTZ-140
廠商： Analog Devices Inc
文件頁數： 15/28頁
文件大小： 0K
描述： IC FLAT PANEL INTERFACE 80-LQFP
標準包裝： 90
應用： 顯示器，監控器，電視
接口： 模擬
電源電壓： 3 V ~ 3.6 V
封裝/外殼： 80-LQFP
供應商設備封裝： 80-LQFP（14x14）
包裝： 托盤
安裝類型： 表面貼裝
產品目錄頁面： 788 (CN2011-ZH PDF)
REV. B
AD9883A
–22–
Table XXXIV. Detected Coast Input Polarity Status
Polarity Status
Result
0Coast Polarity Negative
1Coast Polarity Positive
This indicates that Bit 1 of Register 5 is the 4:2:2 Output
mode select bit.
15
1
4:2:2 Output Mode Select
A bit that configures the output data in 4:2:2 mode.
This mode can be used to reduce the number of data
lines used from 24 down to 16 for applications using
YUV, YCbCr, or YPbPr graphics signals. A timing
diagram for this mode is shown in Figure 9.
Recommended input and output configurations are
shown in Table XXXV.
Table XXXV. 4:2:2 Output Mode Select
Select
Output Mode
0
4:2:2
1
4:4:4
Table XXXVI. 4:2:2 Input/Output Configuration
Input
Channel
Connection
Output Format
Red
V
U/V
Green
Y
Blue
U
High Impedance
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control interface is provided. Up to two
AD9883A devices may be connected to the 2-wire serial interface,
with each device having a unique address.
The 2-wire serial interface comprises a clock (SCL) and a bidi-
rectional data (SDA) pin. The analog flat panel interface acts as
a slave for receiving and transmitting data over the serial interface.
When the serial interface is not active, the logic levels on SCL
and SDA are pulled high by external pull-up resistors.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL
is high, the serial interface interprets that action as a start or
stop sequence.
There are five components to serial bus operation:
Start Signal
Slave Address Byte
Base Register Address Byte
Data Byte to Read or Write
Stop Signal
When the serial interface is inactive (SCL and SDA are high)
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slaved devices that a data transfer sequence
is coming.
The first eight bits of data transferred after a start signal com-
prise a 7-bit slave address (the first seven bits) and a single R/
W
Bit (the eighth bit). The R/
W Bit indicates the direction of data
transfer, read from (1) or write to (0) the slave device. If the
transmitted slave address matches the address of the device (set by
the state of the SA1-0 input pins in Table XXXIV, the AD9883A
acknowledges by bringing SDA low on the ninth SCL pulse. If the
addresses do not match, the AD9883A does not acknowledge.
Table XXXVII. Serial Port Addresses
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
A6
A5
A4
A3
A2
A1
A0
(MSB)
10
01100
10
01101
Data Transfer via Serial Interface
For each byte of data read or written, the MSB is the first bit of
the sequence.
If the AD9883A does not acknowledge the master device during
a write sequence, the SDA remains high so the master can gen-
erate a stop signal. If the master device does not acknowledge the
AD9883A during a read sequence, the AD9883A interprets this
as “end of data.” The SDA remains high so the master can
generate a stop signal.
Writing data to specific control registers of the AD9883A requires
that the 8-bit address of the control register of interest be written
after the slave address has been established. This control register
address is the base address for subsequent write operations. The
base address autoincrements by one for each byte of data written
after the data byte intended for the base address. If more bytes
are transferred than there are available addresses, the address will
not increment and remains at its maximum value of 14H. Any base
address higher than 14H will not produce an acknowledge signal.
SDA
SCL
tBUFF
tSTAH
tDHO
tDSU
tDAL
tDAH
tSTASU
tSTOSU
Figure 10. Serial Port Read/Write Timing
相關PDF資料
PDF描述
V28C36H100BF CONVERTER MOD DC/DC 36V 100W
LTC4306IGN#PBF IC MUX 4CH 2-WIRE BUS 24-SSOP
MS27468P15B35SA CONN RCPT 37POS JAM NUT W/SCKT
D38999/20FD18SB CONN RCPT 18POS WALL MNT W/SCKT
V28C36H100BL3 CONVERTER MOD DC/DC 36V 100W
相關代理商/技術參數
參數描述
AD9883AKSTZ-RL110 功能描述:IC INTERFACE FLAT 110MHZ 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
AD9883KST-110 制造商:Rochester Electronics LLC 功能描述:110MHZ ANALOG INTERFACE F - Bulk
AD9884 制造商:AD 制造商全稱:Analog Devices 功能描述:100 MSPS/140 MSPS Analog Flat Panel Interface
AD9884A 制造商:AD 制造商全稱:Analog Devices 功能描述:100 MSPS/140 MSPS Analog Flat Panel Interface
AD9884A/PCB 制造商:Analog Devices 功能描述:140 MSPS GRAPHICS DIGITIZER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*