- 您現在的位置：買賣IC網 > PDF目錄8611 > ADA4922-1ARDZ-R7 (Analog Devices Inc)IC ADC DRIVER 18BIT DIFF 8-SOIC PDF資料下載
參數資料
| 型號： | ADA4922-1ARDZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC DRIVER 18BIT DIFF 8-SOIC |
| 標準包裝： | 1,000 |
| 類型： | ADC 驅動器 |
| 應用： | 數據采集 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 8-SOIC-EP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ADA4922-1
Rev. 0 | Page 16 of 20
APPLICATIONS
The ADA4922-1 is a fixed-gain, single-ended-to-differential
voltage amplifier, optimized for driving high resolution ADCs
in high voltage applications. There are no gain adjustments
available to the user.
ADA4922-1 DIFFERENTIAL OUTPUT NOISE MODEL
The principal noise sources in a typical ADA4922-1 application
circuit are shown in Figure 49.
Vn1
VnRg
VnRs
In1
Rs
Rg
VnRf
Rf
OUT–
OUT+
REF
Vn2
05681-
042
Figure 49. ADA4922-1 Differential Output Noise Model
Using the traditional approach, a noise source is applied in
series with one of the inputs of each op amp to model input-
referred voltage noise. The input current noise that matters the
most is present at the input pin. The output voltage noise due to
this noise current depends on the source resistance feeding the
input, as well as the downstream gain in the amplifier. Resistor
noise is modeled by placing a noise voltage source in series with
a noiseless resistor. Rf and Rg are both 600 Ω and therefore have
the same noise voltage density.
At room temperature,
()
Hz
nV/
3.2
Ω
600
kT
4
≈
=
nRf
nRg
V
(2)
The noise at OUT+ is due to the input-referred current and
voltage noise sources of the noninverting amplifier and the
noise of the source resistance, all reflected to the output with a
noise gain of 1, and is equal to:
Voltage Noise @ OUT+: Vn1 + RS(In1) + VnRs
(3)
where RS is the source resistance feeding the input, and VnRs is
the source resistance noise.
The noise at OUT originates from a number of sources:
Voltage Noise @ OUT due to Vn1:
n1
g
f
n1
V
R
V
=
(4)
Voltage Noise
@ OUT due to In1:
()
1
n
S
g
f
n
S
I
R
I
R
=
(5)
Voltage Noise @ OUT due to RS:
nRs
g
f
nRs
V
R
V
=
(6)
Voltage Noise @ OUT due to VnRg:
nRg
g
f
nRg
V
R
V
=
(7)
Voltage Noise @ OUT due to VnRf: VnRF
(8)
Voltage Noise @ OUT due toVn2:
2
1
n
g
f
n2
V
R
V
=
+
(9)
When looking at OUT by itself, the contributing noise sources
are uncorrelated, and therefore, the total output noise is
calculated as the root-sum-square (rss) of the individual
contributors. When looking at the differential output noise, the
noise contributors are uncorrelated except for three, Vn1, RS(In1),
and VnRs, which are common noise sources for both outputs. It
can be seen from the previous results that the output noise due
to Vn1, RS(In1), and VnRs each appear at OUT+ with a gain of +1
and at OUT with a gain of 1. This produces a gain of 2 for each
of these three sources at the differential output.
The total differential output noise density is calculated as
Von,dm =
(
)
(
) ()
2
4
Hz
nV/
3.2
2
)
Hz
pA/
(1.4
2
n
nRs
s
n
V
R
V
+
(10)
where Vn1 = Vn2 ≡ Vn = 3.9 nV/√Hz; the input referred voltage
noise of each amplifier is the same.
The output noise due to the amplifier alone is calculated by
setting RS and VnRs equal to zero. In this case:
Von, dm = 12 nV/√Hz
(11)
Clearly, the output noise is not balanced between the outputs,
but this is not an issue in most applications.
USING THE REF PIN
The REF pin sets the output baseline in the inverting path and
is used as a reference for the input signal. In most applications,
the REF pin is set to the input signal midswing level, which in
many cases is also midsupply. For bipolar signals and power
supplies, REF is generally set to ground. In single-supply
applications, setting REF to the input signal midswing level
provides optimal output dynamic range performance with
minimum differential offset. Note that the REF input only
affects the inverting signal path, or OUT.
Most applications require a differential output signal with the
same dc common-mode level on each output. It is possible for
the signal measured across OUT+ and OUT to have a common-
mode voltage that is of the desired level but has different dc
levels at both outputs. Typically, this situation is avoided,
because it wastes the amplifier’s output dynamic range.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24B-MW-B1 | CONVERTER MOD DC/DC 95V 100W |
| ADA4922-1ACPZ-RL7 | IC ADC DRVR 18BIT HV DIFF 8LFCSP |
| VE-24L-IV-F1 | CONVERTER MOD DC/DC 28V 150W |
| VE-24K-IV-F4 | CONVERTER MOD DC/DC 40V 150W |
| VE-24K-IV-F3 | CONVERTER MOD DC/DC 40V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4922-1ARDZ-RL | 功能描述:IC ADC DRIVER 18BIT DIFF 8-SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| ADA4927-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultralow Distortion Current Feedback Differential ADC Driver |
| ADA4927-1YCP-EBZ | 功能描述:BOARD EVAL FOR ADA4927-1YCP RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ADA4927-1YCPZ-R2 | 制造商:Analog Devices 功能描述:SP Amp Differential ADC Driver Single 11V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:SP AMP DIFFERENTIAL ADC DRVR SGL 11V 16LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:ANAADA4927-1YCPZ-R2 ULTRALW DISTORTION C 制造商:Analog Devices 功能描述:OP AMP CF DIFF 65MA LN 16LFCSP 制造商:Analog Devices 功能描述:OP AMP, CF, DIFF, 65MA, LN, 16LFCSP 制造商:Analog Devices 功能描述:OP AMP, CF, DIFF, 65MA, LN, 16LFCSP; No. of Amplifiers:1; Input Offset Voltage:1.3mV; Bandwidth:2.3GHz; Amplifier Case Style:LFCSP; No. of Pins:16; Supply Voltage Range:4.5V to 11V; Slew Rate:5000V/s; Supply Current:20mA; Operating ;RoHS Compliant: Yes |
| ADA4927-1YCPZ-R2 | 制造商:Analog Devices 功能描述:IC DIFF AMP 2.3GHZ 5000V/ LFCSP-16 |
發布緊急采購，3分鐘左右您將得到回復。