參數資料
型號： ADA4930-1YCP-EBZ
廠商： Analog Devices Inc
文件頁數： 10/29頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR ADA4930-1YCP
標準包裝： 1
每 IC 通道數： 1 - 單
放大器類型： 差分
板類型： 裸（未填充）
已供物品： 板
已用 IC / 零件： 16-LFCSP 封裝
ADA4930-1/ADA4930-2
Rev. A | Page 17 of 28
THEORY OF OPERATION
The ADA4930-1/ADA4930-2 differ from conventional op amps
in that they have two outputs whose voltages move in opposite
directions and an additional input, VOCM. Like an op amp, they rely
on high open-loop gain and negative feedback to force these
outputs to the desired voltages. The ADA4930-1/ADA4930-2
behave much like standard voltage feedback op amps and facilitate
single-ended-to-differential conversions, common-mode level
shifting, and amplifications of differential signals. Like op amps,
the ADA4930-1/ADA4930-2 have high input impedance and low
output impedance.
Two feedback loops control the differential and common-mode
output voltages. The differential feedback, set with external
resistors, controls the differential output voltage. The common-
mode feedback controls the common-mode output voltage. This
architecture makes it easy to set the output common-mode level
to any arbitrary value within the specified limits. The output
common-mode voltage is forced to be equal to the voltage applied
to the VOCM input by the internal common-mode feedback loop.
The internal common-mode feedback loop produces outputs
that are highly balanced over a wide frequency range without
requiring tightly matched external components. This results
in differential outputs that are very close to the ideal of being
identical in amplitude and are exactly 180°apart in phase.
ANALYZING AN APPLICATION CIRCUIT
The ADA4930-1/ADA4930-2 use high open-loop gain and
negative feedback to force their differential and common-mode
output voltages to minimize the differential and common-mode
error voltages. The differential error voltage is defined as the
voltage between the differential inputs labeled +IN and IN
(see Figure 42). For most purposes, this voltage can be assumed
to be zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
SETTING THE CLOSED-LOOP GAIN
The differential-mode gain of the circuit in Figure 42 is
determined by
G
F
dm
IN
dm
OUT
R
V
=
,
where the gain and feedback resistors,
RG and RF, on each side
are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
The differential output noise of the ADA4930-1/ADA4930-2 can
be estimated using the noise model in Figure 43. The input-referred
noise voltage density, vnIN, is modeled as differential. The noise
currents, inIN and inIN+, appear between each input and ground.
ADA4930
+
RF2
VnOD
VnCM
VOCM
VnIN
RF1
RG2
RG1
VnRF1
VnRF2
VnRG1
VnRG2
inIN+
inIN–
09
20
9-
0
50
Figure 43. Noise Model
Similar to the case of conventional op amps, the output noise
voltage densities can be estimated by multiplying the input-
referred terms at +IN and IN by an appropriate output factor.
The output voltage due to vnIN is obtained by multiplying vnIN by
the noise gain, GN.
The circuit noise gain is
()
2
1
N
β
G
+
=
2
where the feedback factors are
G1
F1
G1
1
R
β
+
=
and
G2
F2
G2
2
R
β
+
=
.
When the feedback factors are matched, RF1/RG1 = RF2/RG2,
β1 = β2 = β, and the noise gain becomes
G
F
N
R
β
G
+
=
1
.
The noise currents are uncorrelated with the same mean-square
value, and each produces an output voltage that is equal to the
noise current multiplied by the associated feedback resistance.
The noise voltage density at the VOCM pin is vnCM. When the
feedback networks have the same feedback factor, as in most
cases, the output noise due to vnCM is common-mode and the
output noise from VOCM is zero.
Each of the four resistors contributes (4kTRxx)1/2. The noise
from the feedback resistors appears directly at the output, and
the noise from the gain resistors appears at the output multiplied
by RF/RG.
The total differential output noise density, vnOD, is the root-sum-
square of the individual output noise terms.
∑
=
8
1
i
2
)
(
nODi
nOD
v
相關PDF資料
PDF描述
ECM18DRTI-S13 CONN EDGECARD 36POS .156 EXTEND
7-1589455-2 WDUALOBE CONNECTOR
SRR0905-270M INDUCTOR POWER 27UH 1.3A SMD
SP1210R-124K INDUCTOR PWR SHIELDED 120UH SMD
202D221-25/86-0 BOOT MOLDED
相關代理商/技術參數
參數描述
ADA4930-1YCPZ 制造商:Analog Devices 功能描述:IC AMP DIFF 1.35GHZ 16-LFCSP 制造商:Analog Devices 功能描述:IC, AMP, DIFF, 1.35GHZ, 16-LFCSP 制造商:Analog Devices 功能描述:IC, AMP, DIFF, 1.35GHZ, 16-LFCSP; No. of Amplifiers:1; Input Offset Voltage:350V; Bandwidth:1.35GHz; Amplifier Case Style:LFCSP; No. of Pins:16; Supply Voltage Range:3.3V, 5V; Slew Rate:3400V/s; Supply Current:34mA; Operating ;RoHS Compliant: Yes
ADA4930-1YCPZ-R2 功能描述:IC DIFF AMP 1.35GHZ 16-LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR)
ADA4930-1YCPZ-R7 功能描述:差分放大器 UltraLow Dist Low Vltg ADC Driver RoHS:否 制造商:Analog Devices 通道數量:1 Channel 帶寬:900 MHz 可用增益調整:5.6 dB to 20 dB 輸入補償電壓:1 mV at 5 V 共模抑制比（最小值）:67 dB 工作電源電壓:11 V 電源電流:28 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ADA4930-1YCPZ-R7_PROMO 制造商:Analog Devices 功能描述:IC DIFF AMPLIFIER 1.35GHZ L
ADA4930-1YCPZ-RL 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 5.5V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ULTRALOW DIST LOW VLTG ADC DRIVER - Tape and Reel 制造商:Analog Devices Inc. 功能描述:Differential Amplifiers UltraLow Dist Low Vltg ADC Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*