- 您現在的位置：買賣IC網 > PDF目錄16955 > ADA4930-1YCP-EBZ (Analog Devices Inc)BOARD EVAL FOR ADA4930-1YCP PDF資料下載
參數資料
| 型號： | ADA4930-1YCP-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADA4930-1YCP |
| 標準包裝： | 1 |
| 每 IC 通道數： | 1 - 單 |
| 放大器類型： | 差分 |
| 板類型： | 裸（未填充） |
| 已供物品： | 板 |
| 已用 IC / 零件： | 16-LFCSP 封裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
ADA4930-1/ADA4930-2
Rev. A | Page 19 of 28
MINIMUM RG VALUE
Due to the wide bandwidth of the ADA4930-1/ADA4930-2, the
value of RG must be greater than or equal to 301 Ω at unity gain
to provide sufficient damping in the amplifier front end. In the
terminated case, RG includes the Thevenin resistance of the
source and load terminations.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The VOCM pin of the ADA4930-1/ADA4930-2 is biased at 3/10 of
the total supply voltage above VS with an internal voltage divider.
The input impedance of the VOCM pin is 8.4 kΩ. When relying
on the internal bias, the output common-mode voltage is within
about 100 mV of the expected value.
In cases where accurate control of the output common-mode
level is required, it is recommended that an external source or
resistor divider be used with source resistance less than 100 Ω.
The output common-mode offset listed in the Specifications
section assumes that the VOCM input is driven by a low impedance
voltage source.
It is also possible to connect the VOCM input to a common-mode
voltage (VCM) output of an ADC. However, care must be taken
to ensure that the output has sufficient drive capability. The
input impedance of the VOCM pin is approximately 10 kΩ. If
multiple ADA4930-1/ADA4930-2 devices share one reference
output, it is recommended that a buffer be used.
CALCULATING THE INPUT IMPEDANCE FOR AN
APPLICATION CIRCUIT
The effective input impedance depends on whether the signal
source is single-ended or differential. For a balanced differential
between the inputs (+DIN and DIN) is RIN, dm = 2 × RG.
+VS
ADA4930
+IN
–IN
RF
+DIN
–DIN
VOCM
RG
VOUT, dm
09
20
9-
0
51
Figure 44. ADA4930-1/ADA4930-2 Configured for Balanced (Differential) Inputs
For an unbalanced single-ended input signal, as shown in
Figure 45, the input impedance is
RIN,SE = RG1
)
1
(
+
β2
β1
β2
β1
where:
β1 =
F1
G1
R
+
β2 =
2
F
G2
G
R
+
ADA4930
RL VOUT, dm
+VS
–VS
RG1
RG2
RF2
RF1
VOCM
RIN, SE
0
92
09
-05
2
Figure 45. ADA4930-1/ADA4930-2 with Unbalanced (Single-Ended) Input
For a balanced system where RG1 = RG2 = RG and RF1 = RF2 = RF,
the equations simplify to
+
=
+
=
)
2(
1
F
G
F
G
IN,SE
F
G
R
and
R
β2
β1
The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the input resistor RG1. The common-mode
voltage at the amplifier input terminals can be easily determined
by noting that the voltage at the inverting input is equal to the
noninverting output voltage divided down by the voltage divider
formed by RF2 and RG2. This voltage is present at both input
terminals due to negative voltage feedback and is in phase
with the input signal, thus reducing the effective voltage across
RG1, partially bootstrapping it.
相關PDF資料 |
PDF描述 |
|---|---|
| ECM18DRTI-S13 | CONN EDGECARD 36POS .156 EXTEND |
| 7-1589455-2 | WDUALOBE CONNECTOR |
| SRR0905-270M | INDUCTOR POWER 27UH 1.3A SMD |
| SP1210R-124K | INDUCTOR PWR SHIELDED 120UH SMD |
| 202D221-25/86-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADA4930-1YCPZ | 制造商:Analog Devices 功能描述:IC AMP DIFF 1.35GHZ 16-LFCSP 制造商:Analog Devices 功能描述:IC, AMP, DIFF, 1.35GHZ, 16-LFCSP 制造商:Analog Devices 功能描述:IC, AMP, DIFF, 1.35GHZ, 16-LFCSP; No. of Amplifiers:1; Input Offset Voltage:350V; Bandwidth:1.35GHz; Amplifier Case Style:LFCSP; No. of Pins:16; Supply Voltage Range:3.3V, 5V; Slew Rate:3400V/s; Supply Current:34mA; Operating ;RoHS Compliant: Yes |
| ADA4930-1YCPZ-R2 | 功能描述:IC DIFF AMP 1.35GHZ 16-LFCSP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| ADA4930-1YCPZ-R7 | 功能描述:差分放大器 UltraLow Dist Low Vltg ADC Driver RoHS:否 制造商:Analog Devices 通道數量:1 Channel 帶寬:900 MHz 可用增益調整:5.6 dB to 20 dB 輸入補償電壓:1 mV at 5 V 共模抑制比（最小值）:67 dB 工作電源電壓:11 V 電源電流:28 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| ADA4930-1YCPZ-R7_PROMO | 制造商:Analog Devices 功能描述:IC DIFF AMPLIFIER 1.35GHZ L |
| ADA4930-1YCPZ-RL | 制造商:Analog Devices 功能描述:SP Amp DIFF AMP Single 5.5V 16-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ULTRALOW DIST LOW VLTG ADC DRIVER - Tape and Reel 制造商:Analog Devices Inc. 功能描述:Differential Amplifiers UltraLow Dist Low Vltg ADC Driver |
發布緊急采購，3分鐘左右您將得到回復。