- 您現在的位置：買賣IC網 > PDF目錄378283 > ADC12081 (National Semiconductor Corporation) 12-Bit, 5 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold(12位5 MHz可自行校對的管線式帶內部采樣和保持功能A/D轉換器) PDF資料下載
參數資料
| 型號： | ADC12081 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 12-Bit, 5 MHz Self-Calibrating, Pipelined A/D Converter with Internal Sample & Hold(12位5 MHz可自行校對的管線式帶內部采樣和保持功能A/D轉換器) |
| 中文描述： | 12位，5兆赫自校準，流水線A / D轉換器，內置采樣 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 351K |
| 代理商： | ADC12081 |
Applications Information
(Continued)
5.0 Layout and Grounding
Proper grounding and routing of all signals is essential to
ensure accurate conversion. Separate analog and digital
ground planes that are connected beneath the ADC12081
are required to achieve specified performance. The analog
and digital grounds may be in the same layer, but should be
separated from each other and should never overlap each
other. Separation should be at least 1/8 inch, where pos-
sible.
The ground return for the output buffer digital supply (DGND
I/O) carries the ground current for the output drivers. This pin
should be connected to the system digital ground. The cur-
rent on this pin can exhibit high transients that could add
noise to the conversion process. To prevent this from hap-
pening, the DGND I/O pin should NOT be connected in close
proximity to any of the ADC12081’s other ground pins. See .
Capacitive coupling between the typically noisy digital
ground plane and the sensitive analog circuitry can lead to
poor performance that may seem impossible to isolate and
remedy. The solution is to keep the analog circuitry sepa-
rated from the digital circuitry and from the digital ground
plane.
Digital circuits create substantial supply and ground current
transients. The logic noise thus generated could have sig-
nificant impact upon system noise performance. The best
logic family to use in systems with A/D converters is one
which employs non-saturating transistor designs, or has low
noise characteristics, such as the 74LS, 74HC(T) and 74
AC(T)Q families. The worst noise generators are logic fami-
lies that draw the largest supply current transients during
clock or signal edges, like the 74F and the 74AC(T) families.
Since digital switching transients are composed largely of
high frequency components, total ground plane copper
weight will have little effect upon the logic-generated noise.
This is because of the skin effect. Total surface area is more
important than is total ground plane volume.
An effective way to control ground noise is by connecting the
analog and digital ground planes together beneath the ADC
with a copper trace that is very narrow compared with the
rest of the ground plane. This narrowing beneath the con-
verter provides a fairly high impedance to the high frequency
components of the digital switching currents, directing them
away from the analog pins. The relatively lower frequency
analog ground currents do not create a significant voltage
drop across the impedance of this narrow ground connec-
tion.
To maximize accuracy in high speed, high resolution sys-
tems, avoid crossing analog and digital signal traces. It is
important to keep any clock lines isolated from ALL other
lines. Even the generally accepted 90 degree crossing
should be avoided as even a little coupling can cause prob-
lems at high frequencies. This is because other lines can
introduce phase noise (jitter) into the clock line, which can
lead to degradation of SNR.
DS100150-23
FIGURE 5. Basic Connections Diagram
A
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| ADC1210 | ADC1210/ADC1211 12-Bit CMOS A/D Converters |
| ADC1211 | ADC1210/ADC1211 12-Bit CMOS A/D Converters |
| ADC1211HCD | ADC1210/ADC1211 12-Bit CMOS A/D Converters |
| ADC1211HD | 1.5K Bit Serial EPROM with SDQ Interface 3-SOT-23 -20 to 70 |
| ADC1210HCD | ADC1210/ADC1211 12-Bit CMOS A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADC12081_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:12-Bit, 5MHz Self-Calibrating, Pipelined A/D Converter with Internal Samble & Hold |
| ADC12081CIVT | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC12081CIVT/NOPB | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC12081CIVTX | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADC12081CIVTX NOPB | 制造商:National Semiconductor 功能描述:ADC Single Pipelined 5Msps 12-bit Parallel 32-Pin LQFP T/R |
發布緊急采購，3分鐘左右您將得到回復。