- 您現在的位置：買賣IC網 > PDF目錄11485 > ADG4612BRUZ (Analog Devices Inc)IC SWITCH QUAD SPST 16TSSOP PDF資料下載
參數資料
| 型號： | ADG4612BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 設計資源： | Power off protected data acquisition signal chain using ADG4612 , AD711, and AD7476 (CN0165) |
| 標準包裝： | 96 |
| 功能： | 開關 |
| 電路： | 4 x SPST - NO |
| 導通狀態電阻： | 5.1 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±3 V ~ 5.5 V |
| 電流 - 電源： | 600µA |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
ADG4612/ADG4613
Rev. 0 | Page 19 of 24
APPLICATIONS INFORMATION
There are many application scenarios that benefit from the
functionality offered on the ADG4612/ADG4613 switches.
The ADG4612/ADG4613 offer power-off protection, ensuring
the switch is guaranteed off and inputs are high impedance with no
power supplies present. This isolation mode is a useful feature
that isolates the inputs from the outputs where input signals
may be present before supplies. The isolation mode also protects
the system against positive fault conditions that can occur in
applications, ensuring that the switch turns off and protects
downstream circuitry. For example, a module can be connected
to a live backplane, supplying signals to the board before supplies
are present. This is common in hot swap applications where a
card could be hot plugged in a shelf where there are others cards
already working and powered on.
The ADG4612/ADG4613 allow negative signals, down to 5.5 V
to be passed without a negative supply. This can be very useful
in applications that need to pass negative signals but do not
have a negative supply available. This cannot be done with
conventional CMOS switches because ESD protection diodes
turn on and clamp the signals.
Theses features ensure the system is very robust to power
supply sequencing issues that can be present in conventional
CMOS devices.
09
00
5-
0
30
LIVE BACKPLANE
HOT SWAP MODULES
CONTROLLER
HOT SWAP MODULES
POWER SUPPLY
SW
Figure 32. Typical Application
Signals on Inputs with No Power Present
In conventional CMOS switches, ESD protection diodes can be
found on the analog and digital inputs to VDD and GND or VSS
(see Figure 33, for example). If an input voltage is present on the
switch inputs with no power supplies applied, current can flow
through the ESD protection diodes. If this current is not limited
to a safe level, it is possible to damage the ESD protection diodes
and, hence, the switch. Input signals may pass through the switch
to the output affecting downstream circuitry. The user may also
be exceeding the absolute maximum ratings of the devices, and,
therefore, affecting the long-term reliability of the device.
VS
VSS
VDD
RS
RL
Sx
GND
FORWARD
CURRENT
VS > VD
FORWARD
CURRENT
FLOWS
LOAD
CURRENT
Dx
0
900
5-
0
31
Figure 33. ESD Protection Diodes on Conventional CMOS Switch
Some users add external diodes or add current-limiting resistors to
protect the device against the conditions shown in Figure 33.
However, these solutions all have disadvantages in that they add
extra board area, extra component count, and cost. The system
level performance can also be affected by the higher on resistance
from the current-limiting resistors or the higher leakage from
external Schottky diodes. Using external diodes for protection
still creates the problem where a floating VDD line can be pulled
up to a diode drop from the input signal.
VS
VSS
VDD
RS
RL
Sx
GND
Dx
09
00
5-
0
32
FORWARD
CURRENT
LOAD
CURRENT
VS > VD
FORWARD
CURRENT
FLOWS
Figure 34. External Protection Added to Protect Switch Against Damage If
Signals Present on Inputs Without Power Supplies
The ADG4612/ADG4613 eliminate the concerns shown in
Figure 34. There are no internal ESD diodes from the analog or
digital inputs to VDD or VSS. If signals are present on the ADG4612/
ADG4613 inputs before power is present, the switch is in isolation
mode, which means that the inputs have high impedance to
VDD, GND, and the output. This prevents current flow and
protects the device from damage.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4W-CU-F4 | CONVERTER MOD DC/DC 5.5V 200W |
| VE-B4W-CU-F3 | CONVERTER MOD DC/DC 5.5V 200W |
| ADG1604BRUZ | IC MULTIPLEXER 4X1 14TSSOP |
| SST89E58RD2A-40-I-TQJE-T | IC MCU 8BIT 40KB FLASH 44TQFP |
| ADG412BNZ | IC SWITCH QUAD SPST 16DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADG4612BRUZ-REEL7 | 功能描述:模擬開關 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ADG4613BCPZ-REEL7 | 功能描述:IC SWITCH QUAD SPST 16LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ADG4613BRUZ | 功能描述:IC SWITCH QUAD SPST 16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ADG4613BRUZ-REEL7 | 功能描述:模擬開關 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ADG465 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Channel Protector in an SOT-23 Package |
發布緊急采購，3分鐘左右您將得到回復。