- 您現在的位置：買賣IC網 > PDF目錄11485 > ADG4612BRUZ (Analog Devices Inc)IC SWITCH QUAD SPST 16TSSOP PDF資料下載
參數資料
| 型號： | ADG4612BRUZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/24頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16TSSOP |
| 設計資源： | Power off protected data acquisition signal chain using ADG4612 , AD711, and AD7476 (CN0165) |
| 標準包裝： | 96 |
| 功能： | 開關 |
| 電路： | 4 x SPST - NO |
| 導通狀態電阻： | 5.1 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±3 V ~ 5.5 V |
| 電流 - 電源： | 600µA |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
ADG4612/ADG4613
Rev. 0 | Page 17 of 24
THEORY OF OPERATION
The ADG4612/ADG4613 contain four independent single-
pole/single-throw (SPST) switches. Each switch is rail-to-rail
and conducts equally well in both directions when on.
The ADG4612/ADG4613 has two modes of operation: normal
mode and isolation mode.
The operation modes are made possible by a special detection
circuitry that monitors the voltage levels at the source or drain
terminals and VDD relative to ground. Depending on these
voltage levels, the device operates in normal mode or isolation
mode accordingly.
Isolation mode is a useful feature that isolates the inputs from
the outputs where input signals may be present before supplies
or during positive fault conditions that can occur in applications.
Normal Mode
In normal mode, the switch functions as a normal 4 × SPST
switch, whereby the switch is controlled by the logic input pins,
IN1 to IN4.
The following three conditions need to be satisfied for the
switch to be in the on condition;
VDD ≥ 2.7 V; and
Input signal, VS, VD < VDD + VT ; and
Logic input, INx set to on level
When the switch is in the on condition, if the signal range is
from VDD to 5.5 V, the signals present on the switch inputs are
passed through to the switch output. If the analog input exceeds
VDD by a threshold voltage, VT, the switch turns off and is in
isolation mode.
If the analog input signal exceeds the negative supply, VSS, when
the switch is off, the switch blocks a signal up to 5.5 V. If the
switch is on, the switch remains on, and this signal is passed to
the output. See the Negative Fault Condition; Negative Signal
Handling section for more details.
Isolation Mode
In isolation mode, all switches are in the off condition. The
switch inputs are isolated from the switch outputs. The switch
inputs are high impedance inputs with greater than 475 kΩ
impedance to VDD ground and across the switch. This prevents
any current from flowing that can damage the switch. This is
very useful in applications where analog signals may be present
at the switch inputs before power is present or where the user
has no control over the power supply sequence.
The switch is in isolation mode when
No power supplies are present, that is, when VDD is floating
or VDD ≤ 1 V; or
Input signal, VS, VD > VDD + VT
The negative supply rail, VSS, can be floating or 0 V to 5.5 V.
The ground pin must be connected to the ground potential.
Table 11. Switch Operation Mode
VDD
VSS1
GND
VS, VD
(Input Voltage, Sx or Dx)
Switch Condition
Switch
Mode
Floating
X
0 V
5.5 V to +10.5 V
All switches off
Isolation
0 V to 16 V
Inputs isolated from outputs
0 V to 0.8 V
X
0 V
5.5 V to +10.5 V
All switches off
Isolation
0 V to 16 V
Inputs isolated from outputs
VDD ≥ 2.7 V
X
0 V
VS, VD > VDD + VT
All switches off
Isolation
Inputs isolated from outputs
VDD ≥ 2.7 V to 16 V
0 V to 5.5 V
0 V
VDD to VDD – 16 V
Switch state is determined by logic
levels, INx
Normal
1 X = don’t care; for example, floating, 0 V to 5.5 V.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4W-CU-F4 | CONVERTER MOD DC/DC 5.5V 200W |
| VE-B4W-CU-F3 | CONVERTER MOD DC/DC 5.5V 200W |
| ADG1604BRUZ | IC MULTIPLEXER 4X1 14TSSOP |
| SST89E58RD2A-40-I-TQJE-T | IC MCU 8BIT 40KB FLASH 44TQFP |
| ADG412BNZ | IC SWITCH QUAD SPST 16DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADG4612BRUZ-REEL7 | 功能描述:模擬開關 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ADG4613BCPZ-REEL7 | 功能描述:IC SWITCH QUAD SPST 16LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ADG4613BRUZ | 功能描述:IC SWITCH QUAD SPST 16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 功能:開關 電路:單刀單擲 導通狀態電阻:48 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V 電流 - 電源:5µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:托盤 |
| ADG4613BRUZ-REEL7 | 功能描述:模擬開關 IC 5V 4 x SPST Known Power Off RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| ADG465 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Channel Protector in an SOT-23 Package |
發布緊急采購，3分鐘左右您將得到回復。