參數資料
型號： ADM00317
廠商： Microchip Technology
文件頁數： 60/86頁
文件大小： 0K
描述： BOARD DAUGHTER MCP4706/16/26
標準包裝： 1
DAC 的數量： 3 個，每 IC 1 個
位數： 8，10，12
設置時間： 6µs
DAC 型： 電壓
已供物品： 子板
已用 IC / 零件： MCP4706，MCP4716，MCP4726
2011-2012 Microchip Technology Inc.
DS22272C-page 63
MCP4706/4716/4726
8.0
TYPICAL APPLICATIONS
The MCP47X6 family of devices are general purpose,
single channel voltage output DACs for various
applications
where
a
precision
operation
with
low-power and nonvolatile EEPROM memory is
needed.
Since the devices include a nonvolatile EEPROM
memory, the user can utilize these devices for
applications that require the output to return to the
previous set-up value on subsequent power-ups.
Applications generally suited for the devices are:
Set Point or Offset Trimming
Sensor Calibration
Portable Instrumentation (Battery Powered)
Motor Control
8.1
Connecting to I2C BUS using
Pull-Up Resistors
The SCL and SDA pins of the MCP47X6 devices are
open-drain configurations. These pins require a pull-up
resistor as shown in Figure 8-2.
The pull-up resistor values (R1 and R2) for SCL and
SDA pins depend on the operating speed (standard,
fast, and high speed) and loading capacitance of the
I2C bus line. A higher value of the pull-up resistor
consumes less power, but increases the signal
transition time (higher RC time constant) on the bus
line. Therefore, it can limit the bus operating speed.
The lower resistor value, on the other hand, consumes
higher power, but allows higher operating speed. If the
bus line has higher capacitance due to long metal
traces or multiple device connections to the bus line, a
smaller pull-up resistor is needed to compensate the
long RC time constant. The pull-up resistor is typically
chosen between 1 k
Ω and 10 kΩ ranges for Standard
and Fast modes, and less than 1 k
Ω for High-Speed
mode.
8.1.1
DEVICE CONNECTION TEST
The user can test the presence of the device on the I2C
bus line using a simple I2C command. This test can be
achieved by checking an acknowledge response from
the device after sending a Read or Write command.
Figure 8-1 shows an example with a Read command.
The steps are:
a)
Set the R/W bit “High” in the device’s address
byte.
b)
Check the ACK bit of the address byte.
If the device acknowledges (ACK = 0) the
command, then the device is connected,
otherwise it is not connected.
c)
Send Stop bit.
FIGURE 8-1:
I2C Bus Connection Test.
1
2
3
4
5
678
9
SCL
SDA
1
0
1
A2 A1 A0 1
Start
Bit
Address Byte
Address bits
Device Code
R/W
Stop
Bit
Device
AC
K
Response
相關PDF資料
PDF描述
SLP471M200E1P3 CAP ALUM 470UF 200V 20% SNAP
PCX1H330MCL1GS CAP ALUM 33UF 50V 20% SMD
R-725.0D CONV DC/DC 2A 6.5-28VIN 5V
SLPX391M250A5P3 CAP ALUM 390UF 250V 20% SNAP
RBM12DCBD CONN EDGECARD 24POS R/A .156 SLD
相關代理商/技術參數
參數描述
ADM00333 功能描述:開發板和工具包 - PIC / DSPIC PIC18F87J72 Evaluation Board RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
ADM00344 功能描述:電源管理IC開發工具 RE46C190 Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
ADM00345 功能描述:電源管理IC開發工具 3-Phase BLDC Snsrlss Fan Cntrllr RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
ADM00352 功能描述:電源管理IC開發工具 MCP16301 600mA Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
ADM00360 功能描述:電源管理IC開發工具 MCP16301 300mA D2PAK Footprint Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*