- 您現在的位置：買賣IC網 > PDF目錄1898 > ADM1024ARUZ-R7 (ON Semiconductor)IC MONITOR SYS TEMP/VOLT 24TSSOP PDF資料下載
參數資料
| 型號： | ADM1024ARUZ-R7 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 9/30頁 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SYS TEMP/VOLT 24TSSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi Product Discontinuation 30/Sept/2011 |
| 標準包裝： | 1,000 |
| 應用： | PC，PDA |
| 接口： | 串行 |
| 電源電壓： | 2.8 V ~ 5.5 V |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
ADM1024
http://onsemi.com
17
voltage dividers and analog components, will provide best
performance but is not mandatory.
The power supply bypass, the parallel combination of
10
mF (electrolytic or tantalum) and 0.1 mF (ceramic) bypass
capacitors connected between Pin 9 and ground, should also
be located as close as possible to the ADM1024.
Fan Inputs
Pins 5 and 6 may be configured as analog inputs or fan
speed inputs by programming Bits 0 and 1 of the Channel
Mode Register. The power-on default for these bits is all
zeros, which makes Pins 5 and 6 fan inputs.
Signal conditioning in the ADM1024 accommodates the
slow rise and fall times typical of fan tachometer outputs.
The maximum input signal range is 0 to VCC. In the event
that these inputs are supplied from fan outputs that exceed
0 V to 6.5 V, either resistive attenuation of the fan signal or
diode clamping must be included to keep inputs within an
acceptable range.
tachometer outputs.
If the fan tachometer output has a resistive pullup to VCC,
it can be directly connected to the fan input, as shown in
Figure 25.
Figure 25. Fan with Tach Pullup to +VCC
160k
PULLUP
4.7k
TYP
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
W
If the fan output has a resistive pullup to 12 V (or other
voltage greater than 6.5 V), the fan output can be clamped
with a Zener diode, as shown in Figure 26. The Zener
voltage should be chosen so it is greater than VIH but less
than 6.5 V, allowing for the voltage tolerance of the Zener.
A value of between 3.0 V and 5.0 V is suitable.
Figure 26. Fan with Tach. Pullup to Voltage >6.5 V
(e.g., 12 V) Clamped with Zener Diode
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 y VCC.
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
ZD1*
ZENER
160k
PULLUP
4.7k
TYP
W
If the fan has a strong pullup (less than 1 k
W) to 12 V, or
a totem-pole output, then a series resistor can be added to
limit the Zener current, as shown in Figure 27. Alternatively,
a resistive attenuator may be used, as shown in Figure 28.
R1 and R2 should be chosen such that:
(eq. 7)
2.0 V t VPULLUP
R2
RPULLUP ) R1 ) R2
t
t 5.0 V
The fan inputs have an input resistance of nominally
160 k
W to ground, so this should be taken into account when
calculating resistor values.
With a pullup voltage of 12 V and pullup resistor less than
1 k
W, suitable values for R1 and R2 would be 100 kW and
47 k
W. This will give a high input voltage of 3.83 V.
Figure 27. Fan with Strong Tach Pullup to >VCC or
Totem Pole Output, Clamped with Zener and Resistor
*CHOOSE ZD1 VOLTAGE APPROXIMATELY 0.8 y VCC
PULLUP
TOTEMPOLE
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
ZD1*
ZENER
160kW
TYP <1k OR
W
R1
10kW
Figure 28. Fan with Strong Tach Pullup to > VCC or
Totem Pole Output, Attenuated with R1/R2
*SEE TEXT.
12V
VCC
FAN SPEED
COUNTER
FAN1 OR
FAN2
TACH
OUTPUT
R1*
R2*
160k
<1k W
Fan Speed Measurement
The fan counter does not count the fan tachometer output
pulses directly because the fan speed may be less than
1000 rpm and it would take several seconds to accumulate
a reasonably large and accurate count. Instead, the period of
the fan revolution is measured by gating an on-chip
22.5 kHz oscillator into the input of an 8-bit counter for two
periods of the fan tachometer output, as shown in Figure 29;
the accumulated count is actually proportional to the fan
tachometer period and inversely proportional to the fan
speed.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1025ARQZ-R7 | IC MONITOR SYS/VOLT 5CH 16QSOP |
| ADM1181AAN | IC TXRX RS-232 5V 15KV 16DIP |
| ADM1385ARS | IC TXRX RS-232 HI-SP 3.3V 20SSOP |
| ADM1485ARMZ-REEL7 | IC TXRX RS-485 5V HS 8MSOP |
| ADM1486AR | IC TX/RX RS-485 PRO-BUS 5V 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARUZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024EVB | 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1025 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
發布緊急采購，3分鐘左右您將得到回復。