- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1034ARQZ-REEL (ON Semiconductor)IC THERM/FAN SPEED CTRLR 16-QSOP Datasheet資料下載
參數資料
| 型號： | ADM1034ARQZ-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 17/38頁 |
| 文件大?。?/td> | 427K |
| 描述： | IC THERM/FAN SPEED CTRLR 16-QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 2,500 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±1°C |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
ADM1034
http://onsemi.com
17
temperature sensor and the part. The effect of any filter
resistance seen in series with the remote sensor is
automatically cancelled from the temperature.
The construction of a filter allows the ADM1034 and the
remote temperature sensor to operate in noisy environments.
Figure 29 shows a low-pass RCR filter with the following
values: R = 100 W and C = 1 nF. This filtering reduces both
common-mode noise and differential noise.
Figure 29. Filter between Remote Sensor
and ADM1034
100 W
100 W
1 nF
D+
D
REMOTE
TEMPERATURE
SENSOR
Limits, Status Registers, and Interrupts
High and low limits are associated with each measurement
channel on the ADM1034. These can form the basis of system
status monitoring. A status bit can be set for any out-of-limit
condition and detected by polling the device. Alternatively,
SMBusALERT
s can be generated to flag a processor or
microcontroller of an out-of-limit condition.
8-bit Limits
The following is a list of all the 8-bit limits on the
ADM1034:
Table 15. TEMPERATURE LIMIT REGISTERS
Register
Description
Default
0x0B
Local High Limit
0x8B (75癈)
0x0C
Local Low Limit
0x54 (20癈)
0x0D
Local THERM
Limit
0x95 (85癈)
0x0E
Remote 1 High Limit
0x8B (75癈)
0x0F
Remote 1 Low Limit
0x54 (20癈)
0x10
Remote 1 THERM
Limit
0x95 (85癈)
0x11
Remote 2 High Limit
0x8B (75癈)
0x12
Remote 2 Low Limit
0x54 (20癈)
0x13
Remote 2 THERM
Limit
0x95 (85癈)
Table 16. THERM
LIMIT REGISTERS
Register
Description
Default
0x19
THERM
% Limit
0xFF default
Out-of-Limit Comparisons
The ADM1034 measures all parameters in a round-robin
format and sets the appropriate status bit for out-of-limit
conditions. Comparisons are made differently, depending
on whether the measured value is compared to a high or low
limit.
High Limit: ?Comparison Performed
Low Limit: < Comparison Performed
Analog Monitoring Cycle Time
The analog monitoring cycle time begins on powerup, or,
if monitoring has been disabled, by writing a 1 to the
monitor/STBY bit of Configuration Register 1,
(Address 0x01). The ADC measures each one of the analog
inputs in turn; as each measurement is completed, the result
is automatically stored in the appropriate value register. The
round-robin monitoring cycle continues unless it is disabled
by writing a 0 to the monitor/STBY bit (Bit 0) of
Configuration Register 1 (Address 0x01).
The ADC performs round-robin conversions and takes
11 ms for the local temperature measurement and 32 ms for
each remote temperature measurement with averaging
enabled.
The total monitoring cycle time for the average
temperatures is therefore nominally
(2 32) ) 11 + 75 ms
(eq. 2)
Once the conversion time elapses, the round robin starts
again. For more information, refer to the Conversion Rate
Register section.
Fan TACH measurements take place in parallel and are
not synchronized with the temperature measurements in any
way.
Status Registers
The results of limit comparisons are stored in the status
registers. A 1 represents an out-of-limit measurement; a 0
represents an in-limit measurement. The status registers are
located at Addresses 0x4F to 0x51.
If the measurement is outside its limits, the corresponding
status register bit is set to 1. It remains set at 1 until the
measurement falls back within its limits and it is read or until
an ARA is completed.
Poll the state of the various measurements by reading the
status registers over the serial bus. If Bit 0 (ALERT
low) of
Status Register 3 (Address 0x51) is set, this means that the
ALERT
output has been pulled low by the ADM1034.
Pin 14 can be configured as a SMBusALERT
output. This
automatically notifies the system supervisor of an
out-of-limit condition. Reading the status register clears the
status bit as long as the error condition is gone.
Status register bits are sticky. Whenever a status bit is set
due to an out-of-limit condition, it remains set even after the
triggering event has gone. The only way to clear the status
bit is to read the status register (after the event has gone).
Interrupt mask registers (Reg. 0x08, Reg. 0x09, Reg. 0x0A)
allow individual interrupt sources to be masked from
causing an ALERT
. However, if one of these masked
interrupt sources goes out of limit, its associated status bit is
set in the status register.
相關PDF資料 |
PDF描述 |
|---|---|
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
| ADP2140ACPZ3328R7 | IC REG DL BCK/LINEAR 10LFCSP |
| ADP5022ACBZ-6-R7 | IC REG TRPL BCK/LINEAR 16WLCSP |
| ADP5041ACPZ-1-R7 | IC REG TRPL BCK/LINEAR 20-LFCSP |
| ADP5042ACPZ-2-R7 | IC REG TRPL BCK/LINEAR 20LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1034ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1040 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Power Supply Monitor ASIC |
| ADM1041 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。