- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADM1034ARQZ-REEL (ON Semiconductor)IC THERM/FAN SPEED CTRLR 16-QSOP Datasheet資料下載
參數資料
| 型號： | ADM1034ARQZ-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 25/38頁 |
| 文件大?。?/td> | 427K |
| 描述： | IC THERM/FAN SPEED CTRLR 16-QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 2,500 |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±1°C |
| 拓?fù)洌?/td> | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
ADM1034
http://onsemi.com
25
Figure 40. Programming the Look-up Table in
Discreet Fan Speeds Mode
TACH COUNT 8
TACH COUNT 7
TACH COUNT 6
TACH COUNT 5
TACH COUNT 4
TACH COUNT 3
TACH COUNT 2
TACH COUNT 1
T1
T2
T3
T4
T5
T6
T7
T8
TEMPERATURE
FAN SPEED
Figure 41 shows the transfer curve if the Linear Fan
Speeds option is chosen. At temperature T1, the fan runs at
Fan Speed 1. As the temperature increases, the fan speed
increases until it reaches Fan Speed 2 at T2.
Figure 41. Programming the Look-up Table in Linear
Fan Speeds Mode
TACH COUNT 8
T1
TEMPERATURE
FAN SPEED
T2
T3 T4
T5
T6 T7
T8
TACH COUNT 7
TACH COUNT 6
TACH COUNT 5
TACH COUNT 4
TACH COUNT 3
TACH COUNT 2
TACH COUNT 1
Once the temperature exceeds the highest temperature
point in the look-up table, the fan speed remains at the
highest speed until the temperature drops below the T7
temperature value. When the look-up table is split in two, the
same applies.
If the temperatures in T1 to T8 are not programmed in
succession, the fan speed moves to the next highest
programmed temperature as the temperature increases.
Similarly, when the temperature decreases, it ignores
programmed higher temperatures and jumps to the next lower
temperature. Therefore, the temperature-to-fan speed profile
for increasing and decreasing temperature can be different.
When programming the look-up table, the user has the
option to use between two and eight points for each fan
(eight points only if the same curve is to be used for both
fans). If the user just wants to program a transfer curve (and
knows the starting temperature, minimum speed, maximum
temperature, and maximum speed), then all the user needs
to program are four parameters: T1, T2, FS1, and FS2. The
remainder of the look-up temperature thresholds should
remain at their default values of +191癈. If required, the FS3
should be programmed with the same value as FS2 to give
the flat curve, if required. Or, the fan speeds can be left at the
default value of 0. However, it is normal to program a
THERM
limit as well. Once this temperature is exceeded
and the boost bit is set, the fans run to full speed. This
overrides the look-up table.
Figure 42. Programming Two Points on the
Look-up Table
TACH COUNT 2 TO 8
T1
TEMPERATURE
FAN SPEED
T2
TACH COUNT 1
T (3 TO 8) = 癈
Table 30. LOOK-UP TABLE REGISTER ADDRESS
x
Temperature, x
FSx, LSB
FSx, MSB
1
0x22
0x2A
0x2B
2
0x23
0x2C
0x2D
3
0x24
0x2E
0x2F
4
0x25
0x30
0x31
5
0x26
0x32
0x33
6
0x27
0x34
0x35
7
0x28
0x36
0x37
8
0x29
0x38
0x39
Setting Up the Size of the Look-up Table
When 4:8 Look-up (Bit 3) is set to 0 (default), four points
are used for each fan.
When 4:8 Look-up (Bit 3) is set to 1, all eight points on the
table are used for both fans.
Setting Up the Look-up Table in Linear Mode
When Discrete/Linear Speed (Bit 2) is set to 1 (default),
the TACH count decreases linearly (and therefore the fan
speed increases) with temperature.
Example: At temperature T
X
, the fans run at FS
X
and fan
speed increases with temperature to FS
X+1
at temperature
T
X+1
.
Alternatively, the fan can be run at discrete fan speeds.
When Discrete/Linear Speed (Bit 2) is set to 0, the fan runs
at a new speed once the temperature threshold is exceeded.
Setting Which Temperature Channel Controls a Fan
Fan Behavior Register (Address 0x07)
Bits <1:0> = DRIVE1 Behavior (D1B)
Bits <3:2> = DRIVE2 Behavior (D2B)
相關PDF資料 |
PDF描述 |
|---|---|
| ADN8810ACPZ-REEL7 | IC CURRENT SOURCE(12BIT) 24LFCSP |
| ADP2140ACPZ3328R7 | IC REG DL BCK/LINEAR 10LFCSP |
| ADP5022ACBZ-6-R7 | IC REG TRPL BCK/LINEAR 16WLCSP |
| ADP5041ACPZ-1-R7 | IC REG TRPL BCK/LINEAR 20-LFCSP |
| ADP5042ACPZ-2-R7 | IC REG TRPL BCK/LINEAR 20LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1034ARQZ-REEL7 | 功能描述:IC THERM/FAN SPEED CTRLR 16-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1040 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Power Supply Monitor ASIC |
| ADM1041 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Secondary-Side Controller with Current Share and Housekeeping |
| ADM1041AARQZ | 功能描述:IC SECONDARY SIDE CTRLR 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。