參數資料
型號： ADM1490EBRZ-REEL7
廠商： Analog Devices Inc
文件頁數： 2/16頁
文件大?。?/td> 0K
描述： IC TXRX RS485 FULL DUPLEX 8SOIC
標準包裝： 1,000
類型： 收發器
驅動器/接收器數： 1/1
規程： RS422，RS485
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SO
包裝： 帶卷 (TR)
ADM1490E/ADM1491E
Data Sheet
Rev. D | Page 10 of 16
THEORY OF OPERATION
The ADM1490E/ADM1491E are RS-422/RS-485 transceivers that
operate from a single 5 V ± 5% power supply. The ADM1490E/
ADM1491E are intended for balanced data transmission and
comply with both TIA/EIA-485-A and TIA/EIA-422-B. Each
device contains a differential line driver and a differential line
receiver and is suitable for full-duplex data transmission.
The input impedance of the ADM1490E/ADM1491E is 12 k,
allowing up to 32 transceivers on the differential bus. A thermal
shutdown circuit prevents excessive power dissipation caused by
bus contention or by output shorting. This feature forces the driver
output into a high impedance state if, during fault conditions,
a significant temperature increase is detected in the internal
driver circuitry.
The receiver contains a fail-safe feature that results in a logic
high output state if the inputs are unconnected (floating).
The ADM1490E/ADM1491E feature very low propagation delay,
ensuring maximum baud rate operation. The balanced driver
ensures distortion-free transmission.
Another important specification is a measure of the skew between
the complementary outputs. Excessive skew impairs the noise
immunity of the system and increases the amount of electro-
magnetic interference (EMI).
TRUTH TABLES
Table 6. Abbreviations in Truth Tables
Letter
Description
H
High level
I
Indeterminate
L
Low level
X
Irrelevant
Z
High impedance (off)
Table 7. Transmitting
Inputs
Outputs
DE
DI
Z
Y
H
L
H
L
H
L
X
Z
Table 8. Receiving
Inputs
Output
RE
A B
RO
L
≥ +0.2 V
H
L
≤ 0.2 V
L
0.2 V ≤ A B ≤ +0.2 V
I
L
Inputs open
H
X
Z
ESD TRANSIENT PROTECTION SCHEME
The ADM1490E/ADM1491E use protective clamping
structures on their inputs and outputs to clamp the voltage to a
safe level and dissipate the energy present in ESD (electrostatic).
The protection structure achieves ESD protection up to ±8 kV
human body model (HBM).
ESD Testing
Two coupling methods are used for ESD testing: contact dis-
charge and air gap discharge. Contact discharge calls for a direct
connection to the unit being tested; air gap discharge uses a higher
test voltage but does not make direct contact with the unit under
test. With air discharge, the discharge gun is moved toward the
unit under test, developing an arc across the air gap; therefore,
the term air discharge. This method is influenced by humidity,
temperature, barometric pressure, distance, and rate of closure
of the discharge gun. The contact discharge method, though
less realistic, is more repeatable and is gaining acceptance and
preference over the air gap method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time, coupled with high voltages, can cause
failures in unprotected semiconductors. Catastrophic destruction
can occur immediately because of arcing or heating. Even if cata-
strophic failure does not occur immediately, the device can suffer
from parametric degradation, resulting in degraded performance.
The cumulative effects of continuous exposure can eventually
lead to complete failure.
07430-
025
C1
R2
HIGH
VOLTAGE
GENERATOR
DEVICE
UNDER TEST
NOTES
1. THE ESD TEST METHOD USED IS THE
HUMAN BODY MODEL (±8kV) WITH
R2 = 1500 AND C1 = 100pF.
Figure 27. ESD Generator
I/O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I/O cable may result in a static dis-
charge that can damage or destroy the interface product connected
to the I/O port. It is, therefore, extremely important to have high
levels of ESD protection on the I/O lines.
The ESD discharge can induce latch-up in the device under test.
Therefore, it is important to conduct ESD testing on the I/O pins
while power is applied to the device. This type of testing is more
representative of a real-world I/O discharge in which the equip-
ment is operating normally when the discharge occurs.
相關PDF資料
PDF描述
VE-2ND-CU-F4 CONVERTER MOD DC/DC 85V 200W
VE-JWP-MX-S CONVERTER MOD DC/DC 13.8V 75W
VE-23J-MX-F3 CONVERTER MOD DC/DC 36V 75W
ADM1491EBRZ-REEL7 IC TXRX FULLDUP RS485/422 14SOIC
AD7610BCPZ-RL IC ADC 16BIT 250KSPS 48-LFCSP
相關代理商/技術參數
參數描述
ADM1491E 制造商:AD 制造商全稱:Analog Devices 功能描述:16 Mbps, ESD Protected, Full-Duplex RS-485 Transceivers
ADM1491EBRMZ 功能描述:IC TXRX FULLDUP RS485/422 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2
ADM1491EBRMZ-REEL7 功能描述:IC TXRX FULLDUP RS485/422 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件
ADM1491EBRZ 功能描述:IC TXRX FULLDUP RS485/422 14SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2
ADM1491EBRZ-REEL7 功能描述:IC TXRX FULLDUP RS485/422 14SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*