- 您現在的位置：買賣IC網 > PDF目錄1898 > ADM2484EBRWZ-REEL7 (Analog Devices Inc)IC TXRX RS485 ISO W/ESD 16SOIC PDF資料下載
參數資料
| 型號： | ADM2484EBRWZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS485 ISO W/ESD 16SOIC |
| 標準包裝： | 400 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC W |
| 包裝： | 帶卷 (TR) |
| 配用： | EVAL-ADM2484EEBZ-ND - BOARD EVAL FOR ADM2484 |
Data Sheet
ADM2484E
Rev. D | Page 13 of 16
THERMAL SHUTDOWN
The ADM2484E contains thermal shutdown circuitry that
protects the part from excessive power dissipation during fault
conditions. Shorting the driver outputs to a low impedance
source can result in high driver currents. The thermal sensing
circuitry detects the increase in die temperature under this
condition and disables the driver outputs. This circuitry is
designed to disable the driver outputs when a die temperature
of 150°C is reached. As the device cools, the drivers re-enable at
a temperature of 140°C.
TRUE FAIL-SAFE RECEIVER INPUTS
The receiver inputs have a true fail-safe feature ensuring that
the receiver output is high when the inputs are open or shorted.
During line-idle conditions, when no driver on the bus is enabled,
the voltage across a terminating resistor at the receiver input decays
to 0 V. With traditional transceivers, receiver input thresholds
specified between 200 mV and +200 mV mean that external
bias resistors are required on the A and B pins to ensure that the
receiver outputs are in a known state. The true fail-safe receiver
input feature eliminates the need for bias resistors by specifying
the receiver input threshold between 30 mV and 200 mV.
The guaranteed negative threshold means that when the voltage
between A and B decays to 0 V; the receiver output is guaran-
teed to be high.
MAGNETIC FIELD IMMUNITY
The limitation on the magnetic field immunity of the iCoupler
is set by the condition in which an induced voltage in the
receiving coil of the transformer is large enough to either falsely
set or reset the decoder. The following analysis defines the
conditions under which this may occur. The 3 V operating
condition of the ADM2484E is examined because it represents
the most susceptible mode of operation.
The pulses at the transformer output have an amplitude greater
then 1 V. The decoder has a sensing threshold of about 0.5 V,
thus establishing a 0.5 V margin in which induced voltages can
be tolerated.
The voltage induced across the receiving coil is given by
∑π
β
=
2
n
r
dt
d
V
;
N
n
,.
..
,
2
,
1
=
where:
β is the magnetic flux density (gauss).
N is the number of turns in the receiving coil.
rn is the radius of the nth turn in the receiving coil (cm).
Given the geometry of the receiving coil and an imposed
requirement that the induced voltage is, at most, 50% of the
0.5 V margin at the decoder, a maximum allowable magnetic
field can be determined using Figure 26.
MAGNETIC FIELD FREQUENCY (Hz)
1k
10k
100k
100M
1M
10M
100
10
1
0.1
0.01
0.001
M
A
X
IM
U
M
A
LLOWA
B
LE
M
A
GN
E
TIC
F
L
U
X
D
EN
SI
T
Y
(k
G
A
U
SS)
06984-
024
Figure 26. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.2 kgauss induces a
voltage of 0.25 V at the receiving coil. This is about 50% of the
sensing threshold and does not cause a faulty output transition.
Similarly, if such an event occurs during a transmitted pulse and
is the worst-case polarity, it reduces the received pulse from
>1.0 V to 0.75 V, still well above the 0.5 V sensing threshold of
the decoder.
Figure 27 shows the magnetic flux density values in terms of
more familiar quantities, such as maximum allowable current
flow at given distances away from the ADM2484E transformers.
MAGNETIC FIELD FREQUENCY (Hz)
1k
10k
100k
100M
1M
10M
DISTANCE = 1m
DISTANCE = 100mm
DISTANCE = 5mm
1000
100
0.1
1
10
0.01
M
AX
IM
UM
AL
L
O
W
ABL
E
CURRE
NT
(
kA)
06984-
025
Figure 27. Maximum Allowable Current for
Various Current-to-ADM2484E Spacings
With combinations of strong magnetic field and high frequency,
any loops formed by PCB traces can induce error voltages large
enough to trigger the thresholds of succeeding circuitry. Care
should be taken in the layout of such traces to avoid this
possibility.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM2485BRWZ-REEL7 | IC TXRX ISOLATED RS-485 16SOIC |
| ADM2486BRW | IC TXRX RS-485 ISOLATED 16-SOIC |
| ADM2490EBRWZ | IC TXRX RS-485 ISOLATED 16-SOIC |
| ADM2491EBRWZ-REEL7 | IC TXRX HS ESD PROT ISO 16SOIC |
| ADM2587EBRWZ | IC TXRX RS485 ISOLATED 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM2485 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed Isolated RS-485 Transceiver with Integrated Transformer Driver |
| ADM2485_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, Isolated RS-485 Transceiver with Integrated Transformer Driver |
| ADM2485BRMZ | 制造商:Analog Devices 功能描述: |
| ADM2485BRWZ | 功能描述:IC TXRX ISOLATED RS-485 16-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:iCoupler® 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM2485BRWZ-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed Isolated RS-485 Transceiver with Integrated Transformer Driver |
發布緊急采購，3分鐘左右您將得到回復。