- 您現在的位置：買賣IC網 > PDF目錄9673 > ADN2813ACPZ (Analog Devices Inc)IC CLK/DATA REC 1.25GBPS 48LFCSP PDF資料下載
參數資料
| 型號： | ADN2813ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/28頁 |
| 文件大小： | 0K |
| 描述： | IC CLK/DATA REC 1.25GBPS 48LFCSP |
| 標準包裝： | 1 |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | SONET/SDH |
| 輸入： | CML |
| 輸出： | LVDS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.25GHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADN2813
Rev. B | Page 20 of 2
8
For example, if the reference clock frequency is 32 MHz,
SEL_RATE = 1, since the CTRLA[7:6] setting is [01], because
the reference frequency falls into the 20 MHz to 40 MHz range.
Assume for this example that the input data rate is 1.25 Gb/s
(GbE). After following Step 1 through Step 4, the value that is
read back on FREQ[22:0] = 0x138800, which is equal to
1.28 × 106. Plugging this value into the equation yields
The reference clock can range from 10 MHz and 160 MHz.
The ADN2813 expects a reference clock between 10 MHz
and 20 MHz by default. If it is between 20 MHz and 40 MHz,
40 MHz and 80 MHz, or 80 MHz and 160 MHz, the user needs
to configure the ADN2813 to use the correct reference
frequency range by setting two bits of the CTRLA register,
CTRLA[7:6]. Using the reference clock to determine the
frequency of the incoming data does not affect the manner in
which the part locks onto data. In this mode, the reference clock
is used only to determine the frequency of the data. For this
reason, the user does not need to know the data rate to use the
reference clock in this manner.
128e6 × 32e6/2(14 + 1) = 1.25 Gb/s
If subsequent frequency measurements are required, CTRLA[1]
should remain set to 1. It does not need to be reset. The
measurement process is reset by writing a 1 followed by a 0 to
CTRLB[3]. This initiates a new data rate measurement. Follow
Step 2 through Step 4 to read back the new data rate.
Prior to reading back the data rate using the reference clock, the
CTRLA[7:6] bits must be set to the appropriate frequency range
with respect to the reference clock being used. A fine data rate
readback is then executed as follows:
Note that a data rate readback is valid only if LOL is low. If LOL
is high, the data rate readback is invalid.
Additional Features Available via the I2C Interface
Coarse Data Rate Readback
1. Write a 1 to CTRLA[1]. This enables the fine data rate
measurement capability of the ADN2813. This bit is level
sensitive and does not need to be reset to perform
subsequent frequency measurements.
The data rate can be read back over the I2C interface to
approximately ±10% without the need of an external reference
clock. A 9-bit register, COARSE_RD[8:0], can be read back
when LOL is deasserted. The eight MSBs of this register are the
contents of the RATE[7:0] register. The LSB of the
COARSE_RD register is Bit MISC[0].
2. Reset MISC[2] by writing a 1 followed by a 0 to CTRLB[3].
This initiates a new data rate measurement.
3. Read back MISC[2]. If it is 0, the measurement is not
complete. If it is 1, the measurement is complete and the
data rate can be read back on FREQ[22:0]. The time for a
data rate measurement is typically 80 ms.
Table 13 provides coarse data rate readback to within ±10%.
LOS Configuration
The LOS detector output, Pin 22, can be configured to be either
active high or active low. If CTRLC[2] is set to Logic 0 (default),
the LOS pin is active high when a loss-of-signal condition is
detected. Writing a 1 to CTRLC[2] configures the LOS pin to be
active low when a loss-of-signal condition is detected.
4. Read back the data rate from FREQ2[6:0], FREQ1[7:0],
and FREQ0[7:0].
The data rate can be determined by
[]
()
)
_
(
/
..
RATE
SEL
REFCLK
DATARATE
f
FREQ
f
+
×
=
14
2
0
22
System Reset
where:
A frequency acquisition can be initiated by writing a 1 followed
by a 0 to the I2C Register Bit CTRLB[5]. This initiates a new
frequency acquisition while keeping the ADN2813 in the
operating mode that it was previously programmed to in
Registers CTRL[A], CTRL[B], and CTRL[C].
FREQ[22:0] is the reading from FREQ2[6:0] MSByte,
FREQ1[7:0], and FREQ0[7:0] LSByte (see Table 12).
fDATARATE is the data rate (Mb/s).
fREFCLK is the REFCLK frequency (MHz).
SEL_RATE is the setting from CTRLA[7:6].
Table 12.
D22
D21...D17
D16
D15
D14...D9
D8
D7
D6...D1
D0
FREQ2[6:0]
FREQ1[7:0]
FREQ0[7:0]
相關PDF資料 |
PDF描述 |
|---|---|
| AD800-52BRZ | IC CLK\DATA RECOVERY PLL 20SOIC |
| SY87700VZH | IC CLK/DATA RECOVERY 3.3V 28SOIC |
| MS27467P25B35PC | CONN PLUG 128POS STRAIGHT W/PINS |
| AD9558BCPZ | IC CLOCK TRANSLATOR 64LFCSP |
| AD9557BCPZ | IC CLOCK TRANSLATOR 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2813ACPZ-500RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ADN2813ACPZ-RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| ADN2814 | 制造商:Analog Devices 功能描述: |
| ADN2814ACPZ | 功能描述:IC CLOCK/DATA RECOVERY 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| ADN2814ACPZ-500RL7 | 功能描述:IC CLK/DATA REC 675MBPS 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。