- 您現在的位置：買賣IC網 > PDF目錄9673 > ADN2813ACPZ (Analog Devices Inc)IC CLK/DATA REC 1.25GBPS 48LFCSP PDF資料下載
參數資料
| 型號： | ADN2813ACPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/28頁 |
| 文件大小： | 0K |
| 描述： | IC CLK/DATA REC 1.25GBPS 48LFCSP |
| 標準包裝： | 1 |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | SONET/SDH |
| 輸入： | CML |
| 輸出： | LVDS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.25GHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 托盤 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADN2813
Rev. B | Page 12 of
28
TERMINOLOGY
Input Sensitivity and Input Overdrive
Sensitivity and overdrive specifications for the quantizer involve
offset voltage, gain, and noise. The relationship between the
logic output of the quantizer and the analog voltage input is
shown in Figure 12. For sufficiently large positive input voltage,
the output is always Logic 1, and similarly for negative inputs,
the output is always Logic 0. However, the transitions between
output Logic 1 and output Logic 0 are not at precisely defined
input voltage levels but occur over a range of input voltages.
Within this range of input voltages, the output may be either 1
or 0, or it may even fail to attain a valid logic state. The width of
this zone is determined by the input voltage noise of the
quantizer. The center of the zone is the quantizer input offset
voltage. Input overdrive is the magnitude of signal required to
guarantee the correct logic level with 1 × 1010 confidence level.
04951-0-012
NOISE
OUTPUT
INPUT (V p-p)
OFFSET
OVERDRIVE
SENSITIVITY
(2
× OVERDRIVE)
1
0
Figure 12. Input Sensitivity and Input Overdrive
Single-Ended vs. Differential
AC coupling is typically used to drive the inputs to the
quantizer. The inputs are internally dc biased to a common-
mode potential of ~2.5 V. Driving the ADN2813 single-ended
and observing the quantizer input with an oscilloscope probe at
the point indicated in Figure 13 shows a binary signal with an
average value equal to the common-mode potential and
instantaneous values both above and below the average value. It
is convenient to measure the peak-to-peak amplitude of this
signal and call the minimum required value the quantizer
sensitivity. Referring to Figure 13, because both positive and
negative offsets need to be accommodated, the sensitivity is
twice the overdrive. The ADN2813 quantizer typically has
3.3 mV p-p sensitivity.
04951-0-013
SCOPE
PROBE
PIN
50
Ω
3k
Ω
2.5V
50
Ω
VREF
ADN2813
QUANTIZER
+
–
10mV p-p
VREF
Figure 13. Single-Ended Sensitivity Measurement
Driving the ADN2813 differentially (see Figure 14), sensitivity
seems to improve from observing the quantizer input with an
oscilloscope probe. This is an illusion caused by the use of a
single-ended probe. A 5 mV p-p signal appears to drive the
ADN2813 quantizer. However, the single-ended probe
measures only half the signal. The true quantizer input signal is
twice this value, because the other quantizer input is a
complementary signal to the signal being observed.
04951-0-014
SCOPE
PROBE
PIN
50
Ω
3k
Ω
2.5V
50
Ω
VREF
QUANTIZER
+
–
NIN
5mV p-p
VREF
5mV p-p
VREF
Figure 14. Differential Sensitivity Measurement
LOS Response Time
LOS response time is the delay between removal of the input
signal and indication of loss of signal (LOS) at the LOS output,
Pin 22. When the inputs are dc-coupled, the LOS assert time of
the ADN2813 is 500 ns typical and the deassert time is 400 ns
typical. In practice, the time constant produced by the ac
coupling at the quantizer input and the 50 Ω on-chip input
termination determines the LOS response time.
相關PDF資料 |
PDF描述 |
|---|---|
| AD800-52BRZ | IC CLK\DATA RECOVERY PLL 20SOIC |
| SY87700VZH | IC CLK/DATA RECOVERY 3.3V 28SOIC |
| MS27467P25B35PC | CONN PLUG 128POS STRAIGHT W/PINS |
| AD9558BCPZ | IC CLOCK TRANSLATOR 64LFCSP |
| AD9557BCPZ | IC CLOCK TRANSLATOR 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2813ACPZ-500RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ADN2813ACPZ-RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| ADN2814 | 制造商:Analog Devices 功能描述: |
| ADN2814ACPZ | 功能描述:IC CLOCK/DATA RECOVERY 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| ADN2814ACPZ-500RL7 | 功能描述:IC CLK/DATA REC 675MBPS 32-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。