- 您現在的位置：買賣IC網 > PDF目錄165352 > ADP1650ACPZ-R7 (ANALOG DEVICES INC) LED DISPLAY DRIVER, PDSO10 PDF資料下載
參數資料
| 型號： | ADP1650ACPZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED DISPLAY DRIVER, PDSO10 |
| 封裝： | 3 X 3 MM, 0.75 MM WIDTH, ROHS COMPLIANT, LFCSP-10 |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 1423K |
| 代理商： | ADP1650ACPZ-R7 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADP1650
Rev. C | Page 13 of 32
ASSIST LIGHT
The assist light provides continuous current programmable
from 25 mA to 200 mA. Set the assist light current using the
I_TOR bits (in Register 0x03). To enable assist, set LED_MOD
to assist light mode and set OUTPUT_EN = 1 (in Register 0x04).
Disable assist light mode by setting LED_MOD to standby
mode or setting OUTPUT_EN = 0.
LED CURRENT
REG 0x03, I_TOR = XXX mA
REG 0x04, OUTPUT_EN = 1
LED_MOD = 10
I2C DATA BUS
REG 0x04, OUTPUT_EN = 0
0A
I(ASSIST)
0
8837
-007
Figure 27. Enabling Assist Light Mode
FLASH MODE
Flash mode provides 300 mA to 1.5 A for a programmable time
of up to 1.6 seconds. Set the flash current using the I_FL bits (in
Register 0x03) and the maximum flash duration with the FL_TIM
bits (in Register 0x02). To enable flash mode, set LED_MOD
to flash mode and set OUTPUT_EN = 1. Enable flash without
STROBE by setting STR_MODE (in Register 0x04) to 0 (software
strobe). When STR_MODE is in hardware strobe mode, setting
the STROBE pin high enables flash and synchronizes it to the
image sensor. Hardware strobe mode has two modes for timeout:
level sensitive and edge sensitive.
LED CURRENT
REG 0x04, OUTPUT_EN = 1
STR_LV = 1
LED_MOD = 11
I2C DATA BUS
0A
I(FLASH)
STROBE
REG 0x02, FL_TIM = XXXX ms
REG 0x03, I_FL = XXXXX mA
ADP1650 SETS OUTPUT_EN TO 0.
ADP1650 SETS LED_MOD TO 00.
08
83
7-
00
8
Figure 28. Flash Operation: Level-Sensitive Mode
In level-sensitive mode, the duration of STROBE high sets the
duration of the flash up to the maximum time set by the
FL_TIM timeout. If STROBE is kept high longer than the
duration set by FL_TIM, a timeout fault disables the flash.
I2C DATA BUS
LED CURRENT
REG 0x02, FL_TIM = XXXX ms
REG 0x03, I_FL = XXXXX mA
REG 0x04, OUTPUT_EN = 1
STR_LV = 0
LED_MOD = 11
0A
I(FLASH)
STROBE
ADP1650 SETS OUTPUT_EN TO 0.
ADP1650 SETS LED_MOD TO 00.
FL_TIM
08
8
37
-00
9
Figure 29. Flash Operation: Edge-Sensitive Mode
In edge-sensitive mode, a positive edge on the STROBE pin
enables the flash, and the FL_TIM bits set the flash duration.
ASSIST-TO-FLASH OPERATION
LED CURRENT
REG 0x02, FL_TIM = XXXX ms
REG 0x03, I_TOR = XXX mA
REG 0x03, I_FL = XXXXX mA
REG 0x04, OUTPUT_EN = 1
STR_LV = 1
LED_MOD = 10
I2C DATA BUS
0A
I(FLASH)
STROBE
ADP1650 SETS OUTPUT_EN TO 0.
ADP1650 SETS LED_MOD TO 00.
I(ASSIST)
0
883
7-
01
0
Figure 30. Enabling Assist to Flash (Level-Sensitive) Mode
The STR_POL bit in Register 0x07 changes the default enable of
STROBE from low to high to high to low. Additional image
sensor-specific assist/flash enable modes are included in the
device, and information on these is available on request from
the Analog Devices, Inc., sales team.
TORCH MODE
Set the assist/torch light current using the I_TOR bits. To enable
torch mode using a logic signal, set LED_MOD to standby mode
and OUTPUT_EN = 1, and then bring GPIO1 high. Disable
external torch mode by setting GPIO1 low or programming
OUTPUT_EN = 0. Bringing GPIO1 low during torch mode
automatically sets OUTPUT_EN = 0. To enable torch mode
again, program OUTPUT_EN = 1, and bring GPIO high again.
0883
7-
06
5
LED CURRENT
REG 0x03, I_TOR = XXX mA
REG 0x04, OUTPUT_EN = 1
LED_MOD = 00
I2C DATA BUS
0A
I(ASSIST)
ADP1650 SETS OUTPUT_EN TO 0
GPIO1 (TORCH)
Figure 31. Enabling External Torch Mode Using GPIO1
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3157 | 5-Bit Programmable Synchronous Controller for Pentium III Processors |
| ADP3159 | 4-Bit Programmable Synchronous Buck Controllers |
| ADP3162 | 5-Bit Programmable 2-Phase Synchronous Buck Controller |
| ADP3300ART-2.7-RL7 | 2.7 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO6 |
| ADP3300ART-3-REEL7 | 3 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1650CB-EVALZ | 功能描述:EVAL BOARD FOR ADP1650 RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:- 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP1653 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R21 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R7 | 功能描述:IC LED DRVR PHOTO FLASH 16-LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| ADP1653ACPZ-R71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
發布緊急采購，3分鐘左右您將得到回復。