- 您現在的位置：買賣IC網 > PDF目錄165352 > ADP1650ACPZ-R7 (ANALOG DEVICES INC) LED DISPLAY DRIVER, PDSO10 PDF資料下載
參數資料
| 型號： | ADP1650ACPZ-R7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED DISPLAY DRIVER, PDSO10 |
| 封裝： | 3 X 3 MM, 0.75 MM WIDTH, ROHS COMPLIANT, LFCSP-10 |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 1423K |
| 代理商： | ADP1650ACPZ-R7 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADP1650
Rev. C | Page 15 of 32
PROGRAMMABLE BATTERY DC CURRENT LIMIT
The ADP1650 has four optional programmable input dc current
limits that limit the maximum battery current that can be taken
over all conditions. This allows higher LED currents to be used
in a system with significant variation in LED forward voltage
(VF) and supply battery voltage without risk of the current
allocated to the flash being exceeded.
Table 8. Input DC Current Limit Setting the LED Current
Bit Name
Current Limit
IL_DC
00 = 1.5 A
01 = 1.75 A
10 = 2.0 A (default)
11 = 2.25 A
During startup of the flash, if the battery current does not reach
the dc current limit, the LED current is set to the current value
of the I_FL bits. If the battery current does hit the programmed
dc current limit on startup, the LED current does not increase
further. The dc current limit flag is set in the fault information
register. The I_FL bits in Register 0x03 are set to the actual LED
current and are available for readback.
REG 0x02, FL_TIM = XXXX ms
REG 0x03, I_FL = XXXXX mA
IL_DC_EN = 1
IL_DC = XX A
I2C DATA BUS
STROBE
ADP1650 SETS OUTPUT_EN TO 0.
ADP1650 SETS LED_MOD TO 00.
NO LIMIT LED CURRENT
ACTUAL LED CURRENT
ADP1650 SETS FL_IDC (REG 0x05) TO 1.
ADP1650 SETS I_FL TO ACTUAL LED CURRENT.
REG 0x04, OUTPUT_EN = 1
STR_LV = 1
LED_MOD = 11
08
83
7-
0
13
Figure 35. DC Current Limit Operation in a Low Battery, High LED VF Case
The camera system shown in Figure 36 can adjust the image
sensor settings based on the known reduced LED current for a
low battery and a high VF LED.
SELECT FLASH CURRENT
SELECT MAX BATTERY CURRENT
PREFLASH STROBE
DC LIMIT HIT?
LED CURRENT =
PROGAMMED LED
CURRENT
NO
LED CURRENT =
REDUCED LED CURRENT
YES
BATTERY CURRENT =
PROGRAMMED DC LIMIT
I2C READ LED CURRENT
ADJUST IMAGE SENSOR
STROBE
08
83
7-
0
14
Figure 36. Use of the DC Current Limit in an Optimized Camera System
ANALOG-TO-DIGITAL CONVERTER OPERATION
The internal 4-bit analog-to-digital converter (ADC) is configura-
ble to measure the LED VF, integrated circuit (IC) die temperature,
or an external voltage using the GPIO2 pin. Read the 4-bit
resolution output code back from Register 0x08 using the I2C
interface.
INTERFACE/
CONTROL
LED_OUT
SDA
SCL
ADC_EN[1:0]
4-BIT ADC
IC TEMPERATURE
SENSOR
EN
GPIO2
ADC_VAL[5:2]
PTC
0883
7-
01
5
Figure 37. Available ADC Modes in the ADP1650
The ADC can perform the conversion either immediately on an
I2C command, or it can delay the conversion until the next time
the ADP1650 exits an active mode. Delayed conversion can be
useful, for example, for measuring the IC temperature at the
end of a timed flash period. To set up a delayed conversion, set
ADC_EN to the required mode while OUTPUT_EN = 0. Then
set the ADP1650 to the desired output mode (torch, flash assist
light, or 5 V output) and set OUTPUT_EN = 1. The ADC conver-
sion is performed when the ADP1650 exits the chosen mode.
To perform an immediate conversion, set ADC_EN to the
required mode during ADP1650 operation (OUTPUT_EN = 1).
Note that an ADC conversion cannot be performed when the
ADP1650 is idle. This is interpreted as an attempt to set up a
delayed conversion.
LED VF Mode
The ADC can measure the LED VF in both flash and assist/
torch modes. In torch mode, set ADC_EN = 01 to begin a
conversion. The value can be read back from the ADC_VAL[5:2]
bits 1 ms after the conversion has started. Assist/torch mode,
rather than flash mode, is best in the handset production test to
verify the LED VF.
REG 0x08, ADC_EN = 01
START CONVERSION
(INTERNAL SIGNAL)
1ms
ADC_VAL[5:2]
AVAILABLE FOR READ
I2C DATA BUS
08837-
016
Figure 38. ADC Timing for All Modes Except VF Measurement in Flash Mode
In flash mode, set ADC_EN = 01. The conversion happens just
before the timeout occurs; therefore, the FL_TIM bits set when
the ADC sample occurs. This allows the VF to settle from the
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3157 | 5-Bit Programmable Synchronous Controller for Pentium III Processors |
| ADP3159 | 4-Bit Programmable Synchronous Buck Controllers |
| ADP3162 | 5-Bit Programmable 2-Phase Synchronous Buck Controller |
| ADP3300ART-2.7-RL7 | 2.7 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO6 |
| ADP3300ART-3-REEL7 | 3 V FIXED POSITIVE LDO REGULATOR, 0.17 V DROPOUT, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP1650CB-EVALZ | 功能描述:EVAL BOARD FOR ADP1650 RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:- 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP1653 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R21 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
| ADP1653ACPZ-R7 | 功能描述:IC LED DRVR PHOTO FLASH 16-LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| ADP1653ACPZ-R71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Compact, High Efficiency, High Power Flash/Torch LED Driver with Dual Interface |
發布緊急采購，3分鐘左右您將得到回復。