參數資料
型號： ADS7807UBE4
英文描述： Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER
中文描述： 低功耗，16位，采樣CMOS模擬數字轉換器
文件頁數： 12/24頁
文件大小： 534K
代理商： ADS7807UBE4
ADS7807
SBAS022C
12
www.ti.com
FIGURE 6. Conversion and Read Timing with External Clock (
EXT/INT
tied HIGH) Read During a Conversion.
EXTERNAL DATA CLOCK
(After a Conversion)
After conversion
‘
n
’
is completed and the output registers
have been updated,
BUSY
(pin 24) will go HIGH. With
CS
LOW and
R/C
HIGH, valid data from conversion
‘
n
’
will be
output on SDATA (pin 19) synchronized to the external data
clock input on DATACLK (pin 18). The MSB will be valid on
the first falling edge and the second rising edge of the
external data clock. The LSB will be valid on the 16th falling
edge and 17th rising edge of the data clock. TAG (pin 20) will
input a bit of data for every external clock pulse. The first bit
input on TAG will be valid on SDATA on the 17th falling edge
and the 18th rising edge of DATACLK; the second input bit
will be valid on the 18th falling edge and the 19th rising edge,
etc. With a continuous data clock, TAG data will be output on
SDATA until the internal output registers are updated with
the results from the next conversion. Refer to Table VI and
Figure 5.
EXTERNAL DATA CLOCK
(During a Conversion)
After conversion
‘
n
’
has been initiated, valid data from con-
version
‘
n
–
1
’
can be read and will be valid up to 12
μ
s after
the start of conversion
‘
n
’
. Do not attempt to clock out data
from 12
μ
s after the start of conversion
‘
n
’
until
BUSY
(pin 24)
rises; this will result in data loss. NOTE: For the best possible
performance when using an external data clock, data should
not be clocked out during a conversion. The switching noise
of the asynchronous data clock can cause digital feedthrough
degrading the converter
’
s performance. Refer to Table V and
Figure 6.
TAG FEATURE
TAG (pin 20) inputs serial data synchronized to the external
or internal data clock.
When using an external data clock, the serial bit stream input
on TAG will follow the LSB output on SDATA until the internal
output register is updated with new conversion results. See
Table V and Figures 5 and 6.
The logic level input on TAG for the first rising edge of the
internal data clock will be valid on SDATA after all 16 bits of
valid data have been output.
INPUT RANGES
The ADS7807 offers three input ranges: standard
±
10V and
0V-5V, and a 0V-4V range for complete, single-supply sys-
tems. See Figures 7a and 7b for the necessary circuit
connections for implementing each input range and optional
offset and gain adjust circuitry. Offset and full-scale error
(1)
specifications are tested with the fixed resistors, see Figure
7b. Adjustments for offset and gain are described in the
Calibration section of this data sheet.
The offset and gain are adjusted internally to allow external
trimming with a single supply. The external resistors compen-
sate for this adjustment and can be left out if the offset and
gain will be corrected in software (refer to the Calibration
section).
The input impedance, summarized in Table II, results from
the combination of the internal resistor network (see the front
page of this product data sheet) and the external resistors
NOTE: (1) Full-scale error includes offset and gain errors measured at both
+FS and
–
FS.
EXTERNAL
DATACLK
CS
Bit 15 (MSB)
R/C
BUSY
DATA
TAG
Bit 0 (LSB)
Tag 0
Tag 1
Tag 1
Tag 16
Tag 17
Tag 18
Tag 0
t
20
t
21
t
1
t
11
t
3
t
17
t
18
t
19
t
22
t
20
相關PDF資料
PDF描述
ADS7807UBG4 Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER
ADS7807UE4 Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER
ADS7807PBG4 Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER
ADS7807PG4 Low-Power, 16-Bit, Sampling CMOS ANALOG-to-DIGITAL CONVERTER
ADS7808UBE4 12-Bit 10us Serial CMOS Sampling ANALOG-to-DIGITAL CONVERTER
相關代理商/技術參數
參數描述
ADS7807UBG4 功能描述:模數轉換器 - ADC Low-Power 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS7807UE4 功能描述:模數轉換器 - ADC Low-Power 16-Bit Sampling CMOS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS7807UG4 功能描述:IC 16BIT 40KHZ SMPL ADC 28-SOIC 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 位數:16 采樣率（每秒）:40k 輸入數:1 輸入類型:單端 數據接口:SPI，并聯 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:1 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:5V 特性:- 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:28-SOIC 基本零件編號:ADS7807 標準包裝:20
ADS7808 制造商:BB 制造商全稱:BB 功能描述:12-Bit 10ms Serial CMOS Sampling ANALOG-to-DIGITAL CONVERTER
ADS7808_07 制造商:BB 制造商全稱:BB 功能描述:12-Bit 10us Serial CMOS Sampling ANALOG-to-DIGITAL CONVERTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*