- 您現在的位置：買賣IC網 > PDF目錄17091 > ADS8364M-EVM (Texas Instruments)EVAL MODULE FOR ADS8364 PDF資料下載
參數資料
| 型號： | ADS8364M-EVM |
| 廠商： | Texas Instruments |
| 文件頁數： | 4/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL MODULE FOR ADS8364 |
| 產品培訓模塊： | Data Converter Basics |
| 標準包裝： | 1 |
| ADC 的數量： | 6 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 并聯 |
| 輸入范圍： | 0 ~ 5 V |
| 在以下條件下的電源（標準）： | 413.5mW @ 250kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | ADS8364 |
| 已供物品： | 板 |
| 相關產品： | 296-13449-6-ND - IC ADC LP 16BIT 250KSPS 64TQFP ADS8364Y/2KG4-ND - IC ADC LP 16BIT 250KSPS 64-TQFP ADS8364Y/2K-ND - IC ADC LP 16BIT 250KSPS 64-TQFP ADS8364Y/250G4-ND - IC ADC LP 16BIT 250KSPS 64-TQFP 296-13449-1-ND - IC ADC LP 16BIT 250KSPS 64TQFP 296-13449-2-ND - IC ADC LP 16BIT 250KSPS 64TQFP |
| 其它名稱： | 296-30708 ADS8364M-EVM-ND |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
ADS8364
12
SBAS219C
www.ti.com
TIMING AND CONTROL
The ADS8364 uses an external clock (CLK, pin 28) which
controls the conversion rate of the CDAC. With a 5MHz
external clock, the ADC sampling rate is 250kSPS which
corresponds to a 4
s maximum throughput time. Acquistion
and conversion takes a total of 20 clock cycles.
THEORY OF OPERATION
The ADS8364 contains six 16-bit ADCs that can operate
simultaneously in pairs. The three hold signals (HOLDA,
HOLDB, and HOLDC) initiate the conversion on the specific
channels. A simultaneous hold on all six channels can occur
with all three hold signals strobe together. The converted
values are saved in six registers. For each read operation,
the ADS8364 outputs 16 bits of information (16 Data or 3
Channel Address, Data Valid, and some synchronization
information). The Address/Mode signals (A0, A1, and A2)
select how the data is read from the ADS8364. These
Address/Mode signals can define a selection of a single
channel, a cycle mode that cycles through all channels, or a
FIFO mode that sequences the data determined by the order
of the hold signals. The FIFO mode will allow the six registers
to be used by a single-channel pair and, therefore, three
locations for CH X0 and three locations for CH X1 can be
updated before they are read from the part.
EXPLANATION OF CLOCK, RESET, FD, AND EOC PINS
Clock—An external clock has to be provided for the ADS8364.
The maximum clock frequency is 5MHz. The minimum clock
cycle is 200ns (Timing Diagram, tC1), and the clock has to remain
HIGH (Timing Diagram, tW1) or LOW for at least 60ns.
RESET—Bringing reset signal LOW will reset the ADS8364.
It will clear all the output registers, stop any actual conver-
sions, and will close the sampling switches. The reset signal
has to stay LOW for at least 20ns (see Figure 7, tW4). The
reset signal should be back HIGH for at least 20ns (see
Figure 7, tD2), before starting the next conversion (negative
hold edge).
current into the ADS8364 charges the internal capacitor
array during the sampling period. After this capacitance has
been fully charged, there is no further input current. The
source of the analog input voltage must be able to charge the
input capacitance (25pF) to a 16-bit settling level within 3
clock cycles if the minimum acquisition time is used. When
the converter goes into the hold mode, the input impedance
is greater than 1G
.
Care must be taken regarding the absolute analog input
voltage. The +IN and –IN inputs should always remain within
the range of AGND – 0.3V to AVDD + 0.3V.
TRANSITION NOISE
The transition noise of the ADS8364 itself is low,
as shown in Figure 5. These histograms were generated by
applying a low-noise DC input and initiating 8000 conversions.
The digital output of the ADC will vary in output code due to
the internal noise of the ADS8364. This is true for all 16-bit,
SAR-type ADCs. Using a histogram to plot the output codes,
the distribution should appear bell-shaped with the peak of the
bell curve representing the nominal code for the input value.
The
±1σ, ±2σ, and ±3σ distributions will represent the 68.3%,
95.5%, and 99.7%, respectively, of all codes. The transition
noise can be calculated by dividing the number of codes
measured by 6 and this will yield the
±3σ distribution, or
99.7%, of all codes. Statistically, up to three codes could fall
outside the distribution when executing 1000 conversions.
Remember, to achieve this low-noise performance, the peak-
to-peak noise of the input signal and reference must be
< 50
V.
FIGURE 5. 8000 Conversion Histogram of a DC Input.
FIGURE 6. Level Shift Circuit for Bipolar Input Ranges.
BIPOLAR INPUTS
The differential inputs of the ADS8364 were designed to accept
bipolar inputs (–VREF and +VREF) around the common-mode
voltage (2.5V), which corresponds to a 0V to 5V input range with
a 2.5V reference. By using a simple op amp circuit featuring
four, high-precision external resistors, the ADS8364 can be
configured to accept bipolar inputs. The conventional
±2.5V,
±5V, and ±10V input ranges could be interfaced to the ADS8364
using the resistor values shown in Figure 6.
32807 32808
2726
32805
720
32804
167
32806
680
813
32812
67
32810
32809
906
930
1183
32811
Code
0
32803
0
32813
R
1
R
2
+IN
–IN
REF
OUT (pin 61)
2.5V
4k
20k
Bipolar Input
BIPOLAR INPUT
R
1
R
2
±10V
1k
5k
±5V
2k
10k
±2.5V
4k
20k
OPA227
ADS8364
OPA227
1.2k
1.2k
相關PDF資料 |
PDF描述 |
|---|---|
| AP2111SG-13 | IC USB SWITCH 2.45A CURRENT 8SOP |
| SDR-V | SCOTCH CODE REFILL V |
| AP2281-3FMG-7 | IC LOAD SWITCH SGL P-CH 6-DFN |
| PMF18WE1 | PROCESSOR MODULE FOR ICE4000 |
| ECM18DRTN-S13 | CONN EDGECARD 36POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS8364Y | 制造商:TI 制造商全稱:Texas Instruments 功能描述:250kHz, 16-Bit, 6-Channel Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTERS |
| ADS8364Y/250 | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8364Y/250G4 | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8364Y/2K | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS8364Y/2KG4 | 功能描述:模數轉換器 - ADC 16-Bit 250kSPS 6 ADC Parallel Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。