- 您現在的位置：買賣IC網 > PDF目錄19483 > ADSP-21478BSWZ-2A (Analog Devices Inc)IC DSP SHARC 266MHZ LP 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-21478BSWZ-2A |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 4/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP SHARC 266MHZ LP 100LQFP |
| 標準包裝： | 1 |
| 系列： | SHARC® |
| 類型： | 浮點 |
| 接口： | DAI，DPI，EBI/EMI，I²C，SPI，SPORT，UART/USART |
| 時鐘速率： | 266MHz |
| 非易失內存： | ROM（4Mb） |
| 芯片上RAM： | 3Mb |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.20V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP 裸露焊盤 |
| 供應商設備封裝： | 100-LQFP-EP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Rev. A
|
Page 12 of 72
|
September 2011
The watch dog timer also has an internal RC oscillator that can
be used as the clock source. The internal RC oscillator can be
used as an optional alternative to using an external clock applied
to the WDT_CLIN pin.
Real-Time Clock
The real-time clock (RTC) provides a robust set of digital watch
features, including current time, stopwatch, and alarm. The
RTC is clocked by a 32.768 kHz crystal external to the SHARC
processor. Connect RTC pins RTXI and RTXO with external
components as shown in Figure 3.
The RTC peripheral has dedicated power supply pins so that it
can remain powered up and clocked even when the rest of the
processor is in a low power state. The RTC provides several pro-
grammable interrupt options, including interrupt per second,
minute, hour, or day clock ticks, interrupt on programmable
stopwatch countdown, or interrupt at a programmed alarm
time. An RTCLKOUT signal that operates at 1 Hz is also pro-
vided for calibration.
The 32.768 kHz input clock frequency is divided down to a 1 Hz
signal by a prescaler. The counter function of the timer consists
of four counters: a 60-second counter, a 60-minute counter, a
24-hour counter, and an 32,768-day counter. When the alarm
interrupt is enabled, the alarm function generates an interrupt
when the output of the timer matches the programmed value in
the alarm control register. There are two alarms: The first alarm
is for a time of day. The second alarm is for a day and time of
that day.
The stopwatch function counts down from a programmed
value, with one-second resolution. When the stopwatch inter-
rupt is enabled and the counter underflows, an interrupt is
generated.
SYSTEM DESIGN
The following sections provide an introduction to system design
options and power supply issues.
Program Booting
The internal memory boots at system power-up from an 8-bit
EPROM via the external port, an SPI master, or an SPI slave.
Booting is determined by the boot configuration
(BOOT_CFG2–0) pins in Table 9.
A running reset feature is used to reset the processor core and
peripherals without resetting the PLL and SDRAM controller,
or performing a boot. The functionality of the RESETOUT
/RUNRSTIN pin has now been extended to also act as the input
for initiating a running reset. For more information, see the
ADSP-214xx SHARC Processor Hardware Reference.
Power Supplies
The processors have separate power supply connections for the
internal (VDD_INT) and external (VDD_EXT), power supplies. The
internal and analog supplies must meet the VDD_INT specifica-
tions. The external supply must meet the VDD_EXT specification.
All external supply pins must be connected to the same power
supply.
To reduce noise coupling, the PCB should use a parallel pair of
power and ground planes for VDD_INT and GND.
Target Board JTAG Emulator Connector
Analog Devices DSP Tools product line of JTAG emulators uses
the IEEE 1149.1 JTAG test access port of the processors to mon-
itor and control the target board processor during emulation.
Analog Devices DSP Tools product line of JTAG emulators pro-
vides emulation at full processor speed, allowing inspection and
modification of memory, registers, and processor stacks. The
processor's JTAG interface ensures that the emulator will not
affect target system loading or timing.
For complete information on Analog Devices’ SHARC DSP
Tools product line of JTAG emulator operation, see the appro-
priate emulator hardware user’s guide.
DEVELOPMENT TOOLS
The processors are supported with a complete set of CROSS-
CORE
software and hardware development tools, including
Analog Devices emulators and VisualDSP++
development
environment. The same emulator hardware that supports other
SHARC processors also fully emulates the processors.
EZ-KIT Lite Evaluation Board
For evaluation of the processors, use the EZ-KIT Lite
board
being developed by Analog Devices. The board comes with on-
chip emulation capabilities and is equipped to enable software
development. Multiple daughter cards are available.
Figure 3. External Components for RTC
RTXO
C1
C2
X1
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS. C1 AND C2
SPECIFICATIONS ASSUME BOARD TRACE CAPACITANCE OF 3 pF.
RTXI
R1
Table 9. Boot Mode Selection
BOOT_CFG2–0
1
Booting Mode
000
SPI Slave Boot
001
SPI Master Boot (from Flash and Other Slaves)
010
AMI User Boot (for 8-bit Flash Boot)
011
No Boot (Processor Executes from Internal
ROM After Reset)
100
Reserved
1xx
Reserved
1 The BOOT_CFG2 pin is not available on the 100-lead package.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-20F-CY-F4 | CONVERTER MOD DC/DC 72V 50W |
| ECC22DCAN | CONN EDGECARD 44POS R/A .100 SLD |
| ESM03DRUN | CONN EDGECARD 6POS DIP .156 SLD |
| ADSP-BF516BSWZ-4 | IC DSP 16/32B 400MHZ LP 176LQFP |
| AGM24DTMN | CONN EDGECARD 48POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21478BSWZ-2AX | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-21478KBCZ-1A | 功能描述:IC DSP SHARC 200MHZ LP 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21478KBCZ-2A | 功能描述:IC DSP SHARK 266MHZ 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21478KBCZ-3A | 功能描述:IC DSP SHARK 300MHZ 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21478KCPZ-1A | 功能描述:IC DSP SHARK 200MHZ 88LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。