- 您現在的位置：買賣IC網 > PDF目錄19397 > ADSP-2186MKSTZ-300 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-2186MKSTZ-300 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/40頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 100LQFP |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 主機接口，串行端口 |
| 時鐘速率： | 75MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 40kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 2.50V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
REV. 0
ADSP-2186M
–17–
PROGRAMMABLE I/O
MODE A/PFO
RESET
ERESET
1k
ADSP-2186M
Figure 12. Mode A Pin/EZ-ICE Circuit
See the ADSP-2100 Family EZ-Tools data sheet for complete
information on ICE products.
The ICE-Port interface consists of the following ADSP-2186M
pins:
EBR, EINT, EE, EBG, ECLK, ERESET, ELIN, EMS,
and ELOUT
These ADSP-2186M pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function except
during emulation, and do not require pull-up or pull-down
resistors. The traces for these signals between the ADSP-2186M
and the connector must be kept as short as possible, no longer
than 3 inches.
The following pins are also used by the EZ-ICE:
BR, BG,
RESET, and GND.
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2186M in the target system. This causes the
processor to use its
ERESET, EBR, and EBG pins instead of
the
RESET, BR, and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The female plug is plugged onto the
14-pin connector (a pin strip header) on the target board.
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 13. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.
1
2
34
56
7
8
9
10
11
12
13
14
GND
KEY (NO PIN)
RESET
BR
BG
TOP VIEW
EBG
EBR
ELOUT
EE
EINT
ELIN
ECLK
EMS
ERESET
Figure 13. Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—Pin 7 must be removed from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1
× 0.1 inches. The pin strip header must have
at least 0.15 inch clearance on all sides to accept the EZ- ICE
probe plug.
Pin strip headers are available from vendors such as 3M,
McKenzie, and Samtec.
Target Memory Interface
For your target system to be compatible with the EZ-ICE
emulator, it must comply with the memory interface guidelines
listed below.
PM, DM, BM, IOM, AND CM
Design your Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM), and Composite Memory
(CM) external interfaces to comply with worst case device tim-
ing requirements and switching characteristics as specified in
this data sheet. The performance of the EZ- ICE may approach
published worst-case specification for some memory access
timing requirements and switching characteristics.
Note: If your target does not meet the worst-case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depend-
ing on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statisti-
cally vary in switching characteristic and timing requirements
within published limits.
Restriction: All memory strobe signals on the ADSP-2186M
(
RD, WR, PMS, DMS, BMS, CMS, and IOMS) used in your
target system must have 10 k
pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.
Target System Interface Signals
When the EZ-ICE board is installed, the performance on some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE board:
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
RESET
signal.
EZ-ICE emulation introduces an 8 ns propagation delay
between your target circuitry and the DSP on the
BR signal.
EZ-ICE emulation ignores
RESET and BR when single-
stepping.
EZ-ICE emulation ignores
RESET and BR when in Emulator
Space (DSP halted).
EZ-ICE emulation ignores the state of target
BR in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (
BG) is asserted
by the EZ- ICE board’s DSP.
相關PDF資料 |
PDF描述 |
|---|---|
| RW2-0515D/SMD | CONV DC/DC 2W 4.5-9VIN +/-15VOUT |
| VI-B6P-EU-B1 | CONVERTER MOD DC/DC 13.8V 200W |
| MLP2520S1R0S | INDUCTOR MULTILAYER 1.0UH 1008 |
| TPSC476M016S0110 | CAP TANT 47UF 16V 20% 2312 |
| HSC28DRAI-S734 | CONN EDGECARD 56POS .100 R/A PCB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2186MKSTZ300R | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-2186N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ADSP-2184N-ADSP-2189N: DSP Microcomputer Data Sheet (Rev. 0. 10/01) |
| ADSP-2186NBCA-320 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 144-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:8K PM/8K DM RAM,16-BIT,80 MIPS, 1.8V - Bulk |
| ADSP-2186NBST-320 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:8K PM/8K DM RAM,16-BIT, 80 MIPS, 1.8V - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2186NBSTZ-320 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，FCBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
發(fā)布緊急采購，3分鐘左右您將得到回復。