參數資料
型號： ADSP-TS201SABP-060
廠商： Analog Devices Inc
文件頁數： 8/48頁
文件大小： 0K
描述： IC PROCESSOR 600MHZ 576BGA
標準包裝： 1
系列： TigerSHARC®
類型： 定點/浮點
接口： 主機接口，連接端口，多處理器
時鐘速率： 600MHz
非易失內存： 外部
芯片上RAM： 3MB
電壓 - 輸入/輸出： 2.50V
電壓 - 核心： 1.20V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 576-BBGA 裸露焊盤
供應商設備封裝： 576-BGA-ED（25x25）
包裝： 托盤
配用： ADZS-TS201S-EZLITE-ND - KIT LITE EVAL FOR ADSP-TS201S
Rev. C
|
Page 16 of 48
|
December 2006
ADSP-TS201S
Table 8. Pin Definitions—External Port SDRAM Controller
Signal
Type
Term
Description
MSSD3–0
I/O/T
(pu_0)
nc
Memory Select SDRAM. MSSD0, MSSD1, MSSD2, or MSSD3 is asserted whenever the
DSP accesses SDRAM memory space. MSSD3–0 are decoded memory address pins
that are asserted whenever the DSP issues an SDRAM command cycle (access to
ADDR31:30 = 0b01—except reserved spaces shown in Figure 3 on Page 6). In a multi-
processor system, the master DSP drives MSSD3–0.
RAS
I/O/T
(pu_0)
nc
Row Address Select. When sampled low, RAS indicates that a row address is valid in
a read or write of SDRAM. In other SDRAM accesses, it defines the type of operation
to execute according to SDRAM specification.
CAS
I/O/T
(pu_0)
nc
Column Address Select. When sampled low, CAS indicates that a column address is
valid in a read or write of SDRAM. In other SDRAM accesses, it defines the type of
operation to execute according to the SDRAM specification.
LDQM
O/T
(pu_0)
nc
Low Word SDRAM Data Mask. When sampled high, three-states the SDRAM DQ
buffers. LDQM is valid on SDRAM transactions when CAS is asserted, and inactive on
read transactions. On write transactions, LDQM is active when accessing an odd
address word on a 64-bit memory bus to disable the write of the low word.
HDQM
O/T
(pu_0)
nc
High Word SDRAM Data Mask. When sampled high, three-states the SDRAM DQ
buffers. HDQM is valid on SDRAM transactions when CAS is asserted, and inactive on
read transactions. On write transactions, HDQM is active when accessing an even
address in word accesses or when memory is configured for a 32-bit bus to disable
the write of the high word.
SDA10
O/T
(pu_0)
nc
SDRAM Address Bit 10. Separate A10 signals enable SDRAM refresh operation while
the DSP executes non-SDRAM transactions.
SDCKE
I/O/T
(pu_m/
pd_m)
nc
SDRAM Clock Enable. Activates the SDRAM clock for SDRAM self-refresh or suspend
modes. A slave DSP in a multiprocessor system does not have the pull-up or pull-
down. A master DSP (or ID = 0 in a single processor system) has a pull-up before
granting the bus to the host, except when the SDRAM is put in self refresh mode. In
self refresh mode, the master has a pull-down before granting the bus to the host.
SDWE
I/O/T
(pu_0)
nc
SDRAM Write Enable. When sampled low while CAS is active, SDWE indicates an
SDRAM write access. When sampled high while CAS is active, SDWE indicates an
SDRAM read access. In other SDRAM accesses, SDWE defines the type of operation to
execute according to SDRAM specification.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
相關PDF資料
PDF描述
VE-B3H-CY-S CONVERTER MOD DC/DC 52V 50W
ADSP-21060KSZ-133 IC DSP CONTROLLER 32BIT 240-MQFP
EBC25DRTS CONN EDGECARD 50POS DIP .100 SLD
VE-B3D-CY-S CONVERTER MOD DC/DC 85V 50W
TPSD686K020R0200 CAP TANT 68UF 20V 10% 2917
相關代理商/技術參數
參數描述
ADSP-TS201SABP-10X 制造商:Analog Devices 功能描述:
ADSP-TS201SABP-15X 制造商:Analog Devices 功能描述:
ADSP-TS201SABP-ENG 制造商:Analog Devices 功能描述:
ADSP-TS201SABP-ENG1 制造商:Analog Devices 功能描述:
ADSP-TS201SABPZ050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*