- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7466 (Analog Devices, Inc.) dBCool Remote Thermal Controller and Voltage Monitor PDF資料下載
參數資料
| 型號： | ADT7466 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | dBCool Remote Thermal Controller and Voltage Monitor |
| 中文描述： | dBCool遠程熱控制器和電壓監視器 |
| 文件頁數： | 22/48頁 |
| 文件大?。?/td> | 1269K |
| 代理商： | ADT7466 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADT7466
16-Bit Limits
The fan tach measurements are 16-bit results. The fan tach
limits are also 16 bits, consisting of a high byte and low byte.
Since fans running under speed or stalled are normally the only
conditions of interest, only high limits exist for fan tachs. Since
the fan tach period is actually being measured, exceeding the
limit indicates a slow or stalled fan.
Table 19. Fan Limit Registers
Register
Description
0x4C
TACH1 minimum low byte
0x4D
TACH1 minimum high byte
0x4E
TACH2 minimum low byte
0x4F
TACH2 minimum high byte
Out-of-Limit Comparisons
Once all limits have been programmed, ADT7466 monitoring
can be enabled. The ADT7466 measures all parameters in round-
robin format and sets the appropriate status bit for out-of-limit
conditions. Comparisons are done differently depending on
whether the measured value is being compared to a high or low
limit.
A
greater than
comparison is performed when comparing with
the high limit.
A
less than or equal to
comparison is performed when comparing
with the low limit.
Rev. 0 | Page 22 of 48
Default
0xFF
0xFF
0xFF
0xFF
Status Registers
The results of limit comparisons are stored in Status Register 1
and Status Register 2. The status register bit for each channel
reflects the status of the last measurement and limit comparison
on that channel. If a measurement is within limits, the corre-
sponding status register bit is cleared to 0. If the measurement is
out-of-limits the corresponding status register bit is set to 1.
The state of the various measurement channels can be polled by
reading the status registers over the serial bus. When Bit 7
(OOL) of Status Register 1 (0x10) is 1, an out-of-limit event has
been flagged in Status Register 2. Therefore the user need only
read Status Register 2 when this bit is set. Alternatively, the
ALERT output (Pin 14) can be used as an interrupt, which
automatically notifies the system supervisor of an out-of-limit
condition. Reading the status registers clears the appropriate
status bit as long as the error condition that caused the interrupt
has cleared. Status register bits are sticky, meaning that they
remain set until read by software. Whenever a status bit is set,
indicating an out-of-limit condition, it remains set even if the
event that caused it cleared (until read). The only way to clear
the status bit is to read the status register when the event clears.
Interrupt status mask registers (0x12, 0x13) allow individual
interrupt sources to be masked from causing an ALERT.
However, if one of these masked interrupt sources goes out-of-
limit, its associated status bit is set in the interrupt status
registers.
Table 20. Interrupt Status Register 1 (Reg. 0x10)
Bit No.
Name
Description
7
OOL
1 indicates that a bit in Status Register 2 is set
and that Status Register 2 should be read.
6
AIN1
1 indicates that AIN1 is out of limit.
5
AIN2
1 indicates that AIN2 is out of limit.
4
VCC
1 indicates that V
CC
is out of limit.
3
REM
1 indicates that the remote temperature
measurement is out of limit.
2
LOC
1 indicates that the local temperature
measurement is out of limit.
1
FAN1
1 indicates that the Tach 1 count is above
limit (fan speed below limit).
0
FAN2
1 indicates that the Tach 2 count is above
limit (fan speed below limit).
Table 21. Interrupt Status Register 2 (Reg. 0x11)
Bit No.
Name
Description
5
THRM2
1 indicates that TH1 is open-circuit.
4
THRM1
1 indicates that TH2 is open-circuit.
3
D2
1 indicates that Remote Temperature
Sensing Diode 2 is open-circuit or short-
circuit.
2
D1
1 indicates that Remote Temperature
Sensing Diode 1 is open-circuit or short-
circuit.
1
PHOT
1 indicates that the PROCHOT limit has been
exceeded.
0
OVT
1 indicates that a THERM overtemperature
limit has been exceeded.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7466ARQZ | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL7 | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7516 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
| ADT7519ARQZ1 | SPI/I2C Compatible, Temperature Sensor, Four Channel ADC and Quad Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7466ARQZ | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7466ARQZ-RL7 | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ZEVB | 功能描述:BOARD EVALUATION ADT7466 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。