參數資料
型號: ADT7518ARQZ-REEL
廠商: ANALOG DEVICES INC
元件分類: 溫度/濕度傳感器
英文描述: SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
中文描述: DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 5Cel, RECTANGULAR, SURFACE MOUNT
封裝: LEAD FREE, MO-137-AB, QSOP-16
文件頁數: 38/40頁
文件大?。?/td> 1217K
代理商: ADT7518ARQZ-REEL
ADT7518
Rev. A | Page 38 of 40
D7
D6
D5
D4
D3
D2
D1
X
X
X
X
X
X
X
D0
X
CS
SCLK
DIN
DOUT
1
8
1
8
X
X
X
X
X
X
X
D6
D5
D4
D3
D2
D1
D0
X
D7
CS (CONTINUED)
SCLK (CONTINUED)
DIN (CONTINUED)
DOUT (CONTINUED)
STOP
X
X
X
X
X
X
X
X
1
8
D7
D6
D5
D4
D3
D2
D1
D0
0
START
READ COMMAND
DATA BYTE 1
DATA BYTE 2
Figure 62. SPI—Reading Two Bytes of Data From Two Sequential Registers
CS
SPI
READ OPERATION
WRITE OPERATION
0
Figure 63. SPI—Correct Use of CS During SPI Communication
SMBus/SPI INT/INT
The ADT7518 INT/INT output is an interrupt line for devices
that want to trade their ability to master for an extra pin. It is a
slave device and uses the SMBus/SPI INT/INT to signal the host
device that it wants to talk to. The SMBus/SPI INT/INT on the
ADT7518 is used as an over/under limit indicator.
The INT/INT pin has an open-drain configuration that allows
the outputs of several devices to be wired-AND’ed together
when the INT/INT pin is active low. Use C6 of the Control
Config-uration 1 register to set the active polarity of the
INT/INT out-put. The power-up default is active low. The
INT/INT output can be disabled or enabled by setting C5 of the
Control Config-uration 1 register to 1 or 0, respectively.
The INT/INT output becomes active when either the internal
temperature value, the external temperature value, V
DD
value, or
any of the AIN input values exceed the values in their corres-
ponding T
HIGH
/V
HIGH
or T
LOW
/V
LOW
registers. The INT/INT out-
put goes inactive again when a conversion result has the
measured value back within the trip limits and when the status
register associated with the out-of-limit event is read. The two
interrupt status registers show which event caused the INT/INT
pin to go active.
The INT/INT output requires an external pull-up resistor. This
can be connected to a voltage different from V
DD
, provided the
maximum voltage rating of the INT/INT output pin is not
exceeded. The value of the pull-up resistor depends on the
application but should be large enough to avoid excessive sink
currents at the INT/INT output, which can heat the chip and
affect the temperature reading.
SMBUS ALERT RESPONSE
The INT/INT pin behaves the same way as an SMBus alert pin
when the SMBus/I
2
C interface is selected. It is an open-drain
output and requires a pull-up to V
DD
. Several INT/INT outputs
can be wire-AND’ed together, so that the common line will go
low if one or more of the INT/INT outputs goes low. The polar-
ity of the INT/INT pin must be set active low for a number of
outputs to be wire-AND’ed together.
相關PDF資料
PDF描述
ADT7518ARQZ-REEL7 SPI/I2C Compatible, Temperature Sensor, 4-Channel ADC and Quad Voltage Output DAC
ADUC7020BCP62 Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7021ACP32 Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7021BCP32 Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7021BCP62 Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
相關代理商/技術參數
參數描述
ADT7518ARQZ-REEL7 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R
ADT7519 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI-/I2C-Compatible, Temperature Sensor,4-Channel ADC and Quad Voltage Output
ADT7519ARQ 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP
ADT7519ARQ-REEL 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R
ADT7519ARQ-REEL7 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R 制造商:Analog Devices 功能描述:TEMP SENSOR DGTL SERL (4-WIRE, SPI) 16QSOP - Tape and Reel