參數資料
型號: AL4CS231
英文描述: (512 x9. 1k x9. 2k x9. 4k x9. 8k x9) Synchronous FIFO
中文描述: (512 X9熱賣。經銷商X9熱賣。2k X9熱賣。4K的X9熱賣。8K的X9熱賣)同步FIFO
文件頁數: 9/25頁
文件大小: 2044K
代理商: AL4CS231
AL4CS211/AL4CS221/AL4CS231/AL4CS241/AL4CS251
AL4CS211/AL4CS221/AL4CS231/AL4CS241/AL4CS251
December 14, 2001
9
8.1.2 DATA OUTPUTS (Q8-Q0)
Q8 ~ Q0 are 9-bit wide of output data port.
8.2 Controls
8.2.1 Reset (/RS)
Reset takes place when the Reset (/RS) input is LOW. During reset, both internal read and write
pointers are set to the staring position. A reset is required to initial internal logic after power-up. The
Full Flag (/FF) and Programmable Almost-Full Flag (/PAF) will be reset to HIGH after t
RSF
. The
Empty Flag (/EF) and Programmable Almost-Empty Flag (/PAE) will be reset to LOW after t
RSF
.
During reset, the output register is initialized to all zeros and the offset registers are initialized to their
default values.
8.2.2 Write Clock (WCLK)
A write cycle is initiated on the rising edge of the Write Clock (WCLK). Data setup and hold times
must be met with respect to the rising edge of WCLK. The Full Flag (/FF) and Programmable Almost-
Full Flag (/PAF) are synchronized with respect to the rising edge of the Write Clock (WCLK).
The Write and Read Clocks can be asynchronous or coincident.
8.2.3 Write Enable1 (/WEN1)
If the FIFO is configured to support programmable flags, Write Enable 1 (/WEN1) is the only enable
control pin. In this configuration, when Write Enable 1 (/WEN1) is low, data can be written into the
input register and memory array on the rising edge of every Write Clock (WCLK). Data is stored in
the memory array sequentially and independently of any on going read operation. When Write Enable
1 (/WEN1) is HIGH, the input holds the previous data and no new data can be written into the
memory array. If the FIFO is configured to have two write enables, which allows for depth expansion,
two enable control pins are involved in the write operations. Please refer Write Enable 2 (WEN2)
section for details. To prevent data overflow, the Full Flag (/FF) will go LOW, inhibiting further write
operations. Upon the completion of a valid read cycle, the Full Flag (/FF) will go HIGH after t
WFF
,
allowing a valid write to begin. Write Enable(s) are ignored when the FIFO is full.
8.2.4 Read Clock (RCLK)
Data can be read on the outputs on the rising edge of the Read Clock (RCLK), when all the output
controls /REN1, /REN2, Output Enable (/OE) are set LOW. The Empty Flag (/EF) and
Programmable Almost-Empty Flag (/PAE) are synchronized with respect to the rising edge of the
Read Clock (RCLK). The Write and Read Clocks can be asynchronous or coincident.
8.2.5 Read Enable (/REN1, /REN2)
When both Read Enables (/REN1, /REN2) are LOW, data is read from the memory array to the
output register on the rising edge of the Read Clock (RCLK). When either Read Enable (/REN1,
/REN2) is HIGH, the output register holds the previous data and no new data can to be loaded into
the register. When all the data has been read from the FIFO, the Empty Flag (/EF) will go LOW,
inhibiting further read operations. Once a valid write operation has been done, the Empty Flag (/EF)
will go HIGH after t
REF
and a valid read can begin. The Read Enables (/REN1, /REN2) are ignored
when the FIFO is empty.
相關PDF資料
PDF描述
AL4CS241 (512 x9. 1k x9. 2k x9. 4k x9. 8k x9) Synchronous FIFO
AL4CS251 (512 x9. 1k x9. 2k x9. 4k x9. 8k x9) Synchronous FIFO
ALA110-SERIES ASIC
ALA201 ASIC
ALA202 ASIC
相關代理商/技術參數
參數描述
AL4CS235 制造商:AVERLOGIC 制造商全稱:AVERLOGIC 功能描述:256, 512, 1K, 2K, 4K x 18 Synchronous FIFOs
AL4CS241 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchronous FIFO
AL4CS245 制造商:AVERLOGIC 制造商全稱:AVERLOGIC 功能描述:256, 512, 1K, 2K, 4K x 18 Synchronous FIFOs
AL4CS251 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchronous FIFO
AL4CX263 制造商:AVERLOGIC 制造商全稱:AVERLOGIC 功能描述:16K/32K/64K/128K x9, 8K/16K/32K/64K x18 Synchronous FIFO