<code id="ssp16"><label id="ssp16"></label></code>
  • <dfn id="ssp16"><input id="ssp16"><s id="ssp16"></s></input></dfn>
    <code id="ssp16"><input id="ssp16"></input></code>
  • <table id="ssp16"><tbody id="ssp16"></tbody></table>
            
    
    
    參數資料
    型號: AM29LV065MU40EF
    廠商: Advanced Micro Devices, Inc.
    英文描述: 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    中文描述: 64兆位(8米× 8位)的MirrorBit⑩3.0伏特,只有統一部門閃存記憶體與VersatileI /輸出⑩控制
    文件頁數: 30/62頁
    文件大?。?/td> 778K
    代理商: AM29LV065MU40EF
    28
    Am29LV065MU
    September 12, 2006
    D A T A S H E E T
    The Write Buffer Programming Sequence can be
    aborted in the following ways:
    Load a value that is greater than the page buffer
    size during the Number of Locations to Program
    step.
    Write to an address in a sector different than the
    one specified during the Write-Buffer-Load com-
    mand.
    Write an Address/Data pair to a different
    write-buffer-page than the one selected by the
    Starting Address during the write buffer data load-
    ing stage of the operation.
    Write data other than the Confirm Command after
    the specified number of data load cycles.
    The abort condition is indicated by DQ1 = 1, DQ7 =
    DATA# (for the last address location loaded), DQ6 =
    toggle, and DQ5=0. A Write-to-Buffer-Abort Reset
    command sequence must be written to reset the de-
    vice for the next operation. Note that the full 3-cycle
    Write-to-Buffer-Abort Reset command sequence is re-
    quired when using Write-Buffer-Programming features
    in Unlock Bypass mode.
    Accelerated Program
    The device offers accelerated program operations
    through the ACC pin. When the system asserts V
    HH
    on
    the ACC pin, the device automatically enters the Un-
    lock Bypass mode. The system may then write the
    two-cycle Unlock Bypass program command se-
    quence. The device uses the higher voltage on the
    ACC pin to accelerate the operation.
    Note that the
    ACC pin must not be at V
    HH
    for operations other than
    accelerated programming, or device damage may re-
    sult. In addition, the ACC pin must not be left floating
    or unconnected; inconsistent behavior of the device
    may result.
    Figure 4 illustrates the algorithm for the program oper-
    ation. See the table, “Erase and Program Operations”
    on page 45 for parameters, and Figure 16 for timing di-
    agrams.
    相關PDF資料
    PDF描述
    AM29LV065MU40EI 64 Megabit (8 M x 8-Bit) MirrorBit⑩ 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control
    Am29LV081-90RECB 8 Megabit (1 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory
    AM29LV081-100EC TV 27C 27MIX PIN PLUG RECP
    Am29LV081-120FIB TV 41C 41#20 SKT PLUG RECP
    AM29LV081-150EC TV 4C 4#8(COAX) PIN PLUG RECP
    相關代理商/技術參數
    參數描述
    AM29LV081B-120ED 制造商:Spansion 功能描述:IC SM FLASH 3V 8MB
    AM29LV081B-120ED 制造商:Spansion 功能描述:FLASH MEMORY IC
    AM29LV081B-70EC 制造商:Advanced Micro Devices 功能描述: 制造商:Atmel Corporation 功能描述:
    AM29LV081B-70ED 制造商:Spansion 功能描述:IC FLASH MEMORY PARALLEL 制造商:Advanced Micro Devices 功能描述:NOR Flash, 1M x 8, 40 Pin, Plastic, TSSOP
    AM29LV081B-70ED 制造商:Spansion 功能描述:Flash Memory IC