- 您現在的位置：買賣IC網 > PDF目錄366488 > Am29LV160MB100 (Advanced Micro Devices, Inc.) CAP.FT, 33UF, 10V, 10%,CWR06 PDF資料下載
參數資料
| 型號： | Am29LV160MB100 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | CAP.FT, 33UF, 10V, 10%,CWR06 |
| 中文描述： | 16兆位（2米× 8位/ 1個M x 16位），3.0伏的MirrorBit只引導扇區閃存 |
| 文件頁數： | 25/60頁 |
| 文件大?。?/td> | 1849K |
| 代理商： | AM29LV160MB100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
August 11, 2003 25974B0
Am29LV160M
23
P r e l i m i n a r y
Logical I nhibit
Write cycles are inhibited by holding any one of OE# = V
IL
, CE# = V
IH
or WE# =
V
IH
. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a
logical one.
Pow er-Up W rite I nhibit
If WE# = CE# = V
IL
and OE# = V
IH
during power up, the device does not accept
commands on the rising edge of WE#. The internal state machine is automatically
reset to reading array data on power-up.
Command Definitions
Writing specific address and data commands or sequences into the command
register initiates device operations. Tables
10
–
11
define the valid register com-
mand sequences.
Note that writing incorrect address and data values or writing
them in the improper sequence may place the device in an unknown state. A
reset command is then required to set the device for the next operation.
All addresses are latched on the falling edge of WE# or CE#, whichever happens
later. All data is latched on the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the
“AC Characteristics”
section.
Reading Array Data
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. The device is also ready to read array
data after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the
Erase Suspend mode. The system can read array data using the standard read
timings, except that if it reads at an address within erase-suspended sectors,
the device outputs status data. After completing a programming operation in
the Erase Suspend mode, the system may once again read array data with the
same exception. See
“Erase Suspend/Erase Resume Commands”
for more in-
formation on this mode.
The system
must
issue the reset command to re-enable the device for reading
array data if DQ5 goes high, or while in the autoselect mode. See the
“Reset Com-
mand”
section, next.
See also
“Requirements for Reading Array Data”
in the
“Device Bus Operations”
section for more information. The
Read Operations
table provides the read pa-
rameters, and
Figure 13
shows the timing diagram.
Reset Command
Writing the reset command to the device resets the device to reading array data.
Address bits are don’t care for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the device to read-
ing array data (also applies to programming in Erase Suspend mode). Once
programming begins, however, the device ignores reset commands until the op-
eration is complete.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29LV160MB100EI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MB100FI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| Am29LV160MT100 | CAP 0.01UF 100V 100V X7R RAD.20 .20X.20 BULK M-MIL-PRF-39014 STANDOFF |
| AM29LV160MT100EI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
| AM29LV160MT100FI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) MirrorBit 3.0 Volt-only Boot Sector Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29LV160MB-100EI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 100ns 48-Pin TSOP 制造商:Advanced Micro Devices 功能描述:NOR Flash, 1M x 16, 48 Pin, Plastic, TSSOP |
| AM29LV160MB100PCIT | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 100NS 64BGA - Tape and Reel |
| AM29LV160MB-100WAI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 100ns 48-Pin FBGA |
| AM29LV160MB120EI | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 16M-Bit 2M x 8/1M x 16 120ns 48-Pin TSOP |
| AM29LV160MB70EI | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 70NS 48TSOP - Trays |
發布緊急采購，3分鐘左右您將得到回復。