- 您現在的位置：買賣IC網 > PDF目錄376484 > AM29LV652DU12RMAE (SPANSION LLC) 128 Megabit (16 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIO Control PDF資料下載
參數資料
| 型號： | AM29LV652DU12RMAE |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 128 Megabit (16 M x 8-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileIO Control |
| 中文描述： | 16M X 8 FLASH 3V PROM, 120 ns, PBGA63 |
| 封裝： | 11 X 12 MM, 0.80 MM PITCH, FBGA-63 |
| 文件頁數： | 32/55頁 |
| 文件大?。?/td> | 1181K |
| 代理商： | AM29LV652DU12RMAE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
30
Am29LV652D
October 29, 2004
P R E L I M I N A R Y
Command Definitions
Table 10.
Am29LV652D Command Definitions
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE# (or CE2#) pulse, whichever
happens later.
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE# (or CE2#) pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A22–A16 uniquely select any sector.
Notes:
1.
2.
See
Table 1, on page 9
for description of bus operations.
All values are in hexadecimal.
3.
Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
4.
Unless otherwise noted, address bits A22–A12 are don’t cares.
5.
No unlock or command cycles required when device is in read
mode.
6.
The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when the device is in the autoselect mode, or if DQ5 goes high
(while the device is providing status information).
7.
The fourth cycle of the autoselect command sequence is a read
cycle. See the Autoselect Command Sequence section for more
information.
8.
The data is 00h for an unprotected sector group and 01h for a
protected sector group.
9.
The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
10. The Unlock Bypass Reset command is required to return to the
read mode when the device is in the unlock bypass mode.
11. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
12. The Erase Resume command is valid only during the Erase
Suspend mode.
13. Command is valid when device is ready to read array data or when
device is in autoselect mode.
Command
Sequence
(Note 1)
C
Bus Cycles (Notes 2–4)
Third
Addr
Data
First
Second
Addr
Fourth
Fifth
Sixth
Addr
RA
XXX
XXX
XXX
Data
RD
F0
AA
AA
Data
Addr
Data
Addr
Data
Addr
Data
Read (Note 5)
Reset (Note 6)
Manufacturer ID
Device ID
1
1
4
4
A
Program
Unlock Bypass
XXX
XXX
55
55
XXX
XXX
90
90
X00
X01
01
93
Sector Group Protect Verify
(Note 8)
4
XXX
AA
XXX
55
XXX
90
(SA)X02
00/01
4
3
2
2
6
6
1
1
1
XXX
XXX
AA
AA
XXX
XXX
55
55
XXX
XXX
A0
20
PA
PD
Unlock Bypass Program (Note 9)
XXX
A0
PA
PD
Unlock Bypass Reset (Note 10)
Chip Erase
Sector Erase
Erase Suspend (Note 11)
Erase Resume (Note 12)
CFI Query (Note 13)
XXX
XXX
XXX
BA
BA
XX
90
AA
AA
B0
30
98
XXX
XXX
XXX
00
55
55
XXX
XXX
80
80
XXX
XXX
AA
AA
XXX
XXX
55
55
XXX
SA
10
30
發布緊急采購，3分鐘左右您將得到回復。