- 您現在的位置：買賣IC網 > PDF目錄366528 > AM29PL160CB-70RSI (ADVANCED MICRO DEVICES INC) 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only High Performance Page Mode Flash Memory PDF資料下載
參數資料
| 型號： | AM29PL160CB-70RSI |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | PROM |
| 英文描述： | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only High Performance Page Mode Flash Memory |
| 中文描述： | 1M X 16 FLASH 3V PROM, 70 ns, PDSO44 |
| 封裝： | SO-44 |
| 文件頁數： | 24/44頁 |
| 文件大?。?/td> | 987K |
| 代理商： | AM29PL160CB-70RSI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
June 12, 2002
Am29PL160C
23
condition that indicates the program or erase cycle
was not successfully completed.
The DQ5 failure condition may appear if the system
tries to program a “1” to a location that is previously
programmed to “0.”
Only an erase operation can
change a “0” back to a “1.”
Under this condition, the
device halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a “1.”
Under both these conditions, the system must issue
the reset command to return the device to reading
array data.
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not an
erase operation has begun. (The sector erase timer
does not apply to the chip erase command.) If addi-
tional sectors are selected for erasure, the entire time-
out also applies after each additional sector erase
command. When the time-out is complete, DQ3
switches from “0” to “1.” The system may ignore DQ3
if the system can guarantee that the time between ad-
ditional sector erase commands will always be less than
50
μ
s. See also the “Write Operation Status” section.
After the sector erase command sequence is written,
the system should read the status on DQ7 (Data# Poll-
ing) or DQ6 (Toggle Bit I) to ensure the device has
accepted the command sequence, and then read
DQ3. If DQ3 is “1”, the internally controlled erase cycle
has begun; all further commands (other than Erase
Suspend) are ignored until the erase operation is com-
plete. If DQ3 is “0”, the device will accept additional
sector erase commands. To ensure the command has
been accepted, the system software should check the
status of DQ3 prior to and following each subsequent
sector erase command. If DQ3 is high on the second
status check, the last command might not have been
accepted. Table 11 shows the outputs for DQ3.
START
No
Yes
Yes
DQ5 = 1
No
Yes
Toggle Bit
= Toggle
No
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Read DQ7–DQ0
Toggle Bit
= Toggle
Read DQ7–DQ0
Twice
Read DQ7–DQ0
Notes:
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as DQ5
changes to “1”. See text.
Figure 4.
Toggle Bit Algorithm
(Note 1)
(Notes
1, 2)
相關PDF資料 |
PDF描述 |
|---|---|
| AM29PL160CB-70RSKI | WASHER |
| AM29PL160CB-90 | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only High Performance Page Mode Flash Memory |
| AM29PL160CB90SKI | 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only High Performance Page Mode Flash Memory |
| AM29SL160CB-100WCIN | 16 Megabit CMOS 1.8 Volt-only Super Low Voltage Flash Memory |
| AM29SL160C | 16 Megabit CMOS 1.8 Volt-only Super Low Voltage Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29PL160CB-90SF | 制造商:Advanced Micro Devices 功能描述: |
| AM29PL160CB-90SI | 制造商:SOCO 功能描述: |
| AM29SL160CT-100EIN | 制造商:Advanced Micro Devices 功能描述: |
| AM29SL800DB120WCI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 8MBIT 1MX8/512KX16 120NS 48FBGA - Trays |
| AM29SL800DB90WAD | 制造商:Spansion 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。