- 您現在的位置：買賣IC網 > PDF目錄295067 > AP2007 Synchronous PWM Controller PDF資料下載
參數資料
| 型號： | AP2007 |
| 英文描述： | Synchronous PWM Controller |
| 中文描述： | 同步PWM控制器 |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 181K |
| 代理商： | AP2007 |
AP2007
Synchronous PWM with VFC Controller
(Preliminary)
Anachip Corp
www.anachip.com.tw
Rev. 1.0 Apr 1, 2005
6/7
Function Description (Continued)
Hiccup Mode
During power up, the SS/ SHDN pin is internally
pulled low until VCC reaches the under-voltage
lockout level of 4V. Once VCC has reached 4V, the
SS/ SHDN pin is released and begins to source
10uA of current to the external soft-start capacitor.
As the soft-start voltage rises, the inverting input of
the error comparator is clamped to this voltage.
When the error signal reaches the level of the
internal 0.8V reference, the output voltage is to have
reached its programmed voltage. If an over-current
condition has not occurred the soft-start voltage will
continue to rise and level off at about 2.5V.
An over-current condition occurs when the high-side
drive is turned on, but the PHASE node does not
reach the voltage level set at the OCSET pin. Once
an over-current occurs, the high-side drive is turned
off and the low-side drive turns on and the
SS/ SHDN pin begins to sink 2uA. The soft-start
voltage will begin to decrease as the 2uA of current
discharge the external capacitor. When the soft-start
voltage reaches 0.2V, the SS/ SHDN pin will begin to
source 10uA and begin to charge the external
capacitor causing the soft-start voltage to rise again.
If the over-current condition is no longer present,
normal operation will continue. If the over-current
condition is still present, the SS/ SHDN pin will again
begin to sink 2uA. This cycle will continue indefinitely
until the over-current condition is removed.
In order to prevent substrate glitching, a small-signal
diode should be placed in close proximity to the chip
with cathode connected to PHASE and anode
connected to GND.
Marking Information
(Top View)
SOP-8L
1
8
4
AP2007
YY WW X
Logo
Part No.
ID code: internal
Year: "01" =2001
"02" =2002
Xth week: 01~52
~
5
相關PDF資料 |
PDF描述 |
|---|---|
| AP2007S | Synchronous PWM Controller |
| AP2007SA | Surface Mount Resistors Thick Film Chip Resistors |
| AP2014SG-13 | |
| AP2112K-2.5TRG1 | 2.5 V FIXED POSITIVE LDO REGULATOR, 0.4 V DROPOUT, PDSO5 |
| AP2112R5-1.8TRG1 | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.7 V DROPOUT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AP2007S | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Synchronous PWM Controller |
| AP2007SA | 制造商:ANACHIP 制造商全稱:Anachip Corp 功能描述:Synchronous PWM Controller |
| AP2007SL-13 | 功能描述:開關變換器、穩壓器與控制器 SW REG CNTL BUCK BI 200K 9.5MA 20V 1.25V RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| AP2007SL-U | 功能描述:開關變換器、穩壓器與控制器 SW REG CNTL BUCK BI 200K 9.5MA 20V 1.25V RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| AP2008 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PWM Buck Controller |
發布緊急采購，3分鐘左右您將得到回復。