參數資料
型號： ASC7611
廠商： Electronic Theatre Controls, Inc.
英文描述： HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
中文描述： 五金顯示器整合了風扇控制
文件頁數： 18/40頁
文件大?。?/td> 505K
代理商： ASC7611
P
P
- 18 -
Andigilog, Inc. 2006
www.andigilog.com
October 2006 - 70A05007
aSC7611
Register 42h: Interrupt Status Register 2
Register
Address
Read/
Write
Register Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
42h
R
Interrupt Status 2
ERR2
ERR1
FAN4
FAN3
FAN2
FAN1
RES
12V
00
The Interrupt Status Register 2 bits will be automatically set, by the aSC7611, whenever a fault condition is detected.
Interrupt Status Register 2 identifies faults caused by temperature sensor error, fan speed dropping below minimum set by
the tachometer minimum register. Interrupt Status Register 2 will hold a set bit until the event is read by software. The
contents of this register will be cleared (set to 0) automatically by the aSC7611 after it is read by software, if fault condition
no longer exists. Once set, the Interrupt Status Register 2 bits will remain set until a read event occurs, even if the fault no
longer exists. This register is read-only – a write to this register has no effect.
Bit
Name
R/W
Default
Description
0
12V Limits
Exceeded
R
0
The aSC7611 automatically sets this bit to 1 when the 12V input voltage is
less than or equal to the limit set in the 12V Low Limit register or greater than
the limit set in the 12V High Limit register.
1
RES
R
0
Reserved
2
FAN 1
STALLED
R
0
The aSC7611 automatically sets this bit to 1 when the TACH 1 input reading is
above the count value set in the Tach 1 Minimum MSB and LSB registers.
3
FAN 2
STALLED
R
0
The aSC7611 automatically sets this bit to 1 when the TACH 2 input reading is
above the count value set in the Tach 2 Minimum MSB and LSB registers.
4
FAN 3
STALLED
R
0
The aSC7611 automatically sets this bit to 1 when the TACH 3 input reading is
above the count value set in the Tach 3 Minimum MSB and LSB registers.
5
FAN 4
STALLED
R
0
The aSC7611 automatically sets this bit to 1 when the TACH 4 input reading is
above the count value set in the Tach 4 Minimum MSB and LSB registers.
The aSC7611 automatically sets this bit to 1 when there is an open circuit fault
on the Remote1+ or Remote1- thermal diode input pins. A diode fault will also
set bit 4 Zone 1 Limit bit, of Interrupt Status Register 1.
6
Remote Diode
1 Fault
R
0
7
Remote Diode
2 Fault
R
0
The aSC7611 automatically sets this bit to 1 when there is an open circuit fault
on the Remote2+ or Remote2- thermal diode input pins. A diode fault will also
set bit 6 Zone 3 Limit bit, of Interrupt Status Register 1.
Table 5 Interrupt Status Register 2
Register 43h: VID Register
Register
Address
Read/
Write
Register Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
43h
R
VID0-4
RES
RES
RES
VID4
VID3
VID2
VID1
VID0
00
The VID register contains the values of aSC7611 VID0–VID4 input pins. This register indicates the status of the VID lines
that interconnect the processor to the Voltage Regulator Module (VRM). Software uses the information in this register to
determine the voltage that the processor is designed to operate at. With this information, software can then dynamically
determine the correct values to place in the VCCP Low Limit and VCCP High Limit registers. This register is read-only – a
write to this register has no effect.
Tachometer Measurement and Configuration
Register 28-2Fh: Fan Tachometer Reading
Register
Address
Read/
Write
Register Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
28h
29h
R
R
Tach 1 LS Byte
Tach 1 MS Byte
7
15
6
14
5
13
4
12
3
11
2
10
1
9
0
8
N/A
N/A
2Ah
2Bh
R
R
Tach 2 LS Byte
Tach 2 MS Byte
7
15
6
14
5
13
4
12
3
11
2
10
1
9
0
8
N/A
N/A
2Ch
R
Tach 3 LS Byte
7
6
5
4
3
2
1
0
N/A
相關PDF資料
PDF描述
ASC7611QS24 HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621 HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621QS24 HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASD05H-12S5 Isolated and Regulated 5 WATT Open Frame DC/DC Converter
ASD05H-12S9 Isolated and Regulated 5 WATT Open Frame DC/DC Converter
相關代理商/技術參數
參數描述
ASC7611QS24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC7621QS24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HARDWARE MONITOR WITH INTEGRATED FAN CONTROL
ASC-8-2-CB (5-PIN) 制造商:Belden Inc 功能描述:ASC-8-2-CB (5-PIN)
ASC-8-2-LED PUR 10M(5-CONTACT) 制造商:Belden Inc 功能描述:ASC-8-2-LED PUR 10M(5-CONTACT)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*