參數資料
| 型號： | AT88SA102S-TSU-T |
| 廠商： | Atmel |
| 文件頁數： | 9/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROD AUTHENTICATION SOT23-3 |
| 產品培訓模塊： | CryptoAuthentication™ Introduction |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | AT88SA102S-TSU-TDKR |
17
6.3
BurnFuse
Burns a single one of the status fuse bits (Fuse[64] – Fuse[86]). No other fuses can be burned with this command – use
BurnSecure at personalization time to burn any of the first 88 fuses.
If the BurnFuse enable bit (Fuse 1) has been burned to a zero, then attempts to run this command will return an error.
The power supply pin must meet the VBURN specification during the entire BurnFuse command in order to burn fuses reliably. If
VCC is greater than or equal to 3.7V, then the BurnTime parameter should be set to 0x00 and the internal burn time will be up
to 250
s. If V
CC is less than 3.7V but greater than VBURN then the BurnTime parameter should be set to 0xFFFF and the
internal burn time will be up to 262ms. The chip does not internally check the supply voltage level.
There is a very small interval during tEXEC_BURN when the fuse element is actually being burned. During this interval the power
supply must not be removed and the watchdog timer must not be allowed to expire; or the fuse may end up in a state where it
reads as un-burned but cannot be burned.
Table 6-7.
Input Parameters
Name
Size
Notes
Opcode
BURNFUSE
1
0x04
Param1
FuseNum
1
Which bit within fuse array, minimum value is 64, and maximum value is 86
Param2
BurnTime
2
Must be 0x0000 if Vcc >+3.7 V; must be 0xFFFF otherwise
Data
Ignored
0
Table 6-8.
Output Parameters
Name
Size
Notes
Success
1
Upon successful execution, a value of zero will be returned by AT88SA102S
相關PDF資料 |
PDF描述 |
|---|---|
| AT88SA102S-SH-T | IC BATTERY AUTHENTICATION 8SOIC |
| LFXP6C-3TN144I | IC FPGA 5.8KLUTS 100I/O 144-TQFP |
| ABB66DHFT-S621 | EDGECARD 132PS .050 SMD W/O POST |
| MAX6495ATT+T | IC CNTRLR PROT SW 6TDFN |
| MAX4959ELB+T | IC CTLR HI VOLTAGE OVP 10-UDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT88SA10HS | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:CryptoAuthentication? Host Security Chip |
| AT88SA10HS_10 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Atmel CryptoAuthentication Host Security Chip |
| AT88SA10HS_11 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Atmel CryptoAuthentication Host Security Chip |
| AT88SA10HS-SH-T | 功能描述:序列號注冊 58951-Eb CryptoAuth SHA-256 HST IC GRN RoHS:否 制造商:Maxim Integrated 數據總線寬度: 電源電壓-最大: 電源電壓-最小: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: |
| AT88SA10HS-TH-T | 功能描述:序列號注冊 58951-Eb CryptoAuth SHA-256 HST IC GRN RoHS:否 制造商:Maxim Integrated 數據總線寬度: 電源電壓-最大: 電源電壓-最小: 最大工作溫度: 最小工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。