參數資料
型號： AT89S4051-24PU
廠商： Atmel
文件頁數： 4/46頁
文件大小： 0K
描述： MCU 8051 4K FLASH 24MHZ 20-PDIP
產品培訓模塊： MCU Product Line Introduction
標準包裝： 18
系列： 89S
核心處理器： 8051
芯體尺寸： 8-位
速度： 24MHz
連通性： UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM
輸入/輸出數： 15
程序存儲器容量： 4KB（4K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-DIP（0.300"，7.62mm）
包裝： 管件
12
3390E–MICRO–6/08
AT89S2051/S4051
13. Interrupts
The AT89S2051/S4051 provides 6 interrupt sources: two external interrupts, two timer inter-
rupts, a serial port interrupt, and an analog comparator interrupt. These interrupts and the
system reset each have a separate program vector at the start of the program memory space.
Each interrupt source can be individually enabled or disabled by setting or clearing a bit in the
interrupt enable register IE. The IE register also contains a global disable bit, EA, which disables
all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by setting or
clearing bits in the interrupt priority registers IP and IPH. An interrupt service routine in progress
can be interrupted by a higher priority interrupt, but not by another interrupt of the same or lower
priority. The highest priority interrupt cannot be interrupted by any other interrupt source. If two
requests of different priority levels are pending at the end of an instruction, the request of higher
priority level is serviced. If requests of the same priority level are pending at the end of an
instruction, an internal polling sequence determines which request is serviced. The polling
sequence is based on the vector address; an interrupt with a lower vector address has higher
priority than an interrupt with a higher vector address. Note that the polling sequence is only
used to resolve pending requests of the same priority level.
The External Interrupts INT0 and INT1 can each be either level-activated or transition-activated,
depending on bits IT0 and IT1 in Register TCON. The flags that actually generate these inter-
rupts are the IE0 and IE1 bits in TCON. When the service routine is vectored to, hardware clears
the flag that generated an external interrupt only if the interrupt was transition-activated. If the
interrupt was level activated, then the external requesting source (rather than the on-chip hard-
ware) controls the request flag.
The Timer 0 and Timer 1 Interrupts are generated by TF0 and TF1, which are set by a rollover in
their respective Timer/Counter registers (except for Timer 0 in Mode 3). When a timer interrupt is
generated, the on-chip hardware clears the flag that generated it when the service routine is
vectored to.
The Serial Port Interrupt is generated by the logical OR of RI and TI in SCON. Neither of these
flags is cleared by hardware when the service routine is vectored to. In fact, the service routine
normally must determine whether RI or TI generated the interrupt, and the bit must be cleared in
software.
The CF bit in ACSR generates the Comparator Interrupt. The flag is not cleared by hardware
when the service routine is vectored to and must be cleared by software.
Most of the bits that generate interrupts can be set or cleared by software, with the same result
as though they had been set or cleared by hardware. That is, interrupts can be generated and
pending interrupts can be canceled in software.
Interrupt
Source
Vector Address
System Reset
RST or POR or BOD
0000H
External Interrupt 0
IE0
0003H
Timer 0 Overflow
TF0
000BH
External Interrupt 1
IE1
0013H
Timer 1 Overflow
TF1
001BH
Serial Port
RI or TI
0023H
Analog Comparator
CF
0033H
相關PDF資料
PDF描述
AT89LP2052-20SU IC 8051 MCU FLASH 2K 20SOIC
AT89LP52-20AU IC MCU 8051 8K FLASH SPI 44TQFP
AT89LP52-20PU IC MCU 8051 8K FLASH SPI 40PDIP
ATMEGA48PA-MMN MCU AVR 4KB FLASH 20MHZ 28QFN
ATMEGA48PA-PN MCU AVR 4KB FLASH 20MHZ 28PDIP
相關代理商/技術參數
參數描述
AT89S4051-24SU 功能描述:8位微控制器 -MCU 4K FLASH 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S4051-24SUR 功能描述:8051 89S Microcontroller IC 8-Bit 24MHz 4KB (4K x 8) FLASH 20-SOIC 制造商:atmel 系列:89S 包裝:管件 零件狀態:有效 核心處理器:8051 核心尺寸:8-位 速度:24MHz 連接性:UART/USART 外設:欠壓檢測/復位，POR，PWM I/O 數:15 程序存儲容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:256 x 8 電壓 - 電源（Vcc/Vdd）:2.7 V ~ 5.5 V 數據轉換器:- 振蕩器類型:內部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商器件封裝:20-SOIC 標準包裝:37
AT89S4D12-12RC 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S4D12-12RI 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S51-24AC 功能描述:8位微控制器 -MCU 4K ISP FLASH 2.7 TO 5.5V - 24 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*