參數資料
型號： AT90USB647-MU
廠商： Atmel
文件頁數： 75/106頁
文件大?。?/td> 0K
描述： IC AVR MCU 64K 64QFN
產品培訓模塊： megaAVR Introduction
標準包裝： 1,300
系列： AVR®
應用： USB 微控制器
核心處理器： AVR
程序存儲器類型： 閃存（64 kB）
控制器系列： AT90 USB
RAM 容量： 4K x 8
接口： 2 線串行，SPI 串行，USART，USB
輸入/輸出數： 48
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤
包裝： 托盤
供應商設備封裝： 64-VQFN（9x9）
配用： ATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFP
ATSTK525-ND - KIT STARTER FOR AT90USB
AT90USBKEY2-ND - KIT DEMO FOR AT90USB
其它名稱： AT90USB647-16MU
AT90USB647-16MU-ND
Q4939729A
70
7593L–AVR–09/12
AT90USB64/128
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to Section “Memory programming” on page 359 for details.
To avoid unintentional changes of Interrupt Vector tables, a special write procedure must be fol-
lowed to change the IVSEL bit:
a.
Write the Interrupt Vector Change Enable (IVCE) bit to one.
b.
Within four cycles, write the desired value to IVSEL while writing a zero to IVCE.
Interrupts will automatically be disabled while this sequence is executed. Interrupts are disabled
in the cycle IVCE is set, and they remain disabled until after the instruction following the write to
IVSEL. If IVSEL is not written, interrupts remain disabled for four cycles. The I-bit in the Status
Register is unaffected by the automatic disabling.
Note:
If Interrupt Vectors are placed in the Boot Loader section and Boot Lock bit BLB02 is programmed,
interrupts are disabled while executing from the Application section. If Interrupt Vectors are placed
in the Application section and Boot Lock bit BLB12 is programed, interrupts are disabled while
executing from the Boot Loader section. Refer to the section “Memory programming” on page 359
for details on Boot Lock bits.
Bit 0 – IVCE: Interrupt Vector Change Enable
The IVCE bit must be written to logic one to enable change of the IVSEL bit. IVCE is cleared by
hardware four cycles after it is written or when IVSEL is written. Setting the IVCE bit will disable
interrupts, as explained in the IVSEL description above. See code example below.
Assembly code example
Move_interrupts:
; Get MCUCR
in
r16, MCUCR
mov
r17, r16
; Enable change of Interrupt Vectors
ori
r16, (1<<IVCE)
out
MCUCR, r16
; Move interrupts to Boot Flash section
ori
r17, (1<<IVSEL)
out
MCUCR, r17
ret
C code example
void
Move_interrupts(void)
{
unsigned char temp;
/* Get MCUCR */
temp = MCUCR;
/* Enable change of Interrupt Vectors */
MCUCR = temp | (1<<IVCE);
/* Move interrupts to Boot Flash section */
MCUCR = temp | (1<<IVSEL);
}
相關PDF資料
PDF描述
395-020-527-801 CARD EDGE 20POS DL .100X.200 BLK
395-020-527-204 CARD EDGE 20POS DL .100X.200 BLK
FT24C02A-UNR-T IC EEPROM 2KBIT 1MHZ 8DFN
AYF332365 CONN FPC 23POS SMD Y3BW
AT90USB647-AU IC AVR MCU 64K 64TQFP
相關代理商/技術參數
參數描述
AT90USB647-MUR 功能描述:8位微控制器 -MCU USB 64K FLASH 16 MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90USB64X 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:USB DFU Bootloader
AT90USB82 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 8/16K Bytes of ISP Flash and USB Controller
AT90USB82_0811 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 8/16K Bytes of ISP Flash and USB Controller
AT90USB82-16MU 功能描述:8位微控制器 -MCU AVR USB 8K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*