參數資料
型號: AT91SAM7XC128-CU
廠商: Atmel
文件頁數: 6/47頁
文件大?。?/td> 0K
描述: MCU ARM 128K HS FLASH 100-TFBGA
產品培訓模塊: SAM9 MPU Boot Solutions & Application Deployment
AT91SAM7X and SAM7XC Flash-based Microcontrollers
MCU Product Line Introduction
標準包裝: 260
系列: SAM7XC
核心處理器: ARM7
芯體尺寸: 16/32-位
速度: 55MHz
連通性: CAN,以太網,I²C,SPI,SSC,UART/USART,USB
外圍設備: 欠壓檢測/復位,DMA,POR,PWM,WDT
輸入/輸出數: 62
程序存儲器容量: 128KB(128K x 8)
程序存儲器類型: 閃存
RAM 容量: 32K x 8
電壓 - 電源 (Vcc/Vdd): 1.65 V ~ 1.95 V
數據轉換器: A/D 8x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 100-TFBGA
包裝: 托盤
配用: AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7XC-EK-ND - KIT EVAL FOR AT91SAM7XC256/128
14
6209DS–ATARM–17-Feb-09
AT91SAM7XC512/256/128
6.
I/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are schmitt trigger inputs and are not 5-V tolerant. TMS, TDI and TCK do not
integrate a pull-up resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The
JTAGSEL pin integrates a permanent pull-down resistor of about 15 k
Ω.
To eliminate any risk of spuriously entering the JTAG boundary scan mode due to noise on
JTAGSEL, it should be tied externally to GND if boundary scan is not used, or pulled down with
an external low-value resistor (such as 1 k
Ω) .
6.2
Test Pin
Th e T S T p i n is used f o r ma nu f a ct ur in g t e st o r f a st pr og ra mmi ng mod e of t h e
AT91SAM7XC512/256/128 when asserted high. The TST pin integrates a permanent pull-down
resistor of about 15 k
Ω to GND.
To eliminate any risk of entering the test mode due to noise on the TST pin, it should be tied to
GND if the FFPI is not used, or pulled down with an external low-value resistor (such as 1 k
Ω) .
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high
and PA2 tied to low.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open drain output buffer. It is handled by the on-chip reset
controller and can be driven low to provide a reset signal to the external components or asserted
low externally to reset the microcontroller. There is no constraint on the length of the reset pulse,
and the reset controller can guarantee a minimum pulse length. This allows connection of a sim-
ple push-button on the NRST pin as system user reset, and the use of the signal NRST to reset
all the components of the system.
The NRST pin integrates a permanent pull-up resistor to VDDIO
.
6.4
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a
permanent pull-down resistor of about 15 k
Ω to GND.
To eliminate any risk of erasing the Flash due to noise on the ERASE pin, it shoul be tied exter-
nally to GND, which prevents erasing the Flash from the applicatiion, or pulled down with an
external low-value resistor (such as 1 k
Ω) .
This pin is debounced by the RC oscillator to improve the glitch tolerance. Minimum debouncing
time is 200 ms.
6.5
PIO Controller Lines
All the I/O lines, PA0 to PA30 and PB0 to PB30, are 5V-tolerant and all integrate a programma-
ble pull-up resistor. Programming of this pull-up resistor is performed independently for each I/O
line through the PIO controllers.
相關PDF資料
PDF描述
PIC18F2458-I/SO IC PIC MCU FLASH 12KX16 28SOIC
PIC18F4455-I/P IC PIC MCU FLASH 12KX16 40DIP
AT91SAM7X256-CU MCU ARM 256K HS FLASH 100-TFBGA
PIC16C73B-20/SS IC MCU OTP 4KX14 A/D PWM 28SSOP
PIC18F2550-I/SP IC PIC MCU FLASH 16KX16 28DIP
相關代理商/技術參數
參數描述
AT91SAM7XC128-CU-999 功能描述:ARM微控制器 - MCU BGA Ind. Temp Green RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7XC256 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thumb-based Microcontrollers
AT91SAM7XC256_05 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thumb-based Microcontrollers
AT91SAM7XC256-AU 功能描述:ARM微控制器 - MCU LQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7XC256-AU-999 功能描述:ARM微控制器 - MCU Ind. Temp Green RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT