- 您現在的位置：買賣IC網 > PDF目錄19870 > ATF1504ASVL-20AU44 (Atmel)IC CPLD 20NS LOWV LOW PWR 44TQFP PDF資料下載
參數資料
| 型號： | ATF1504ASVL-20AU44 |
| 廠商： | Atmel |
| 文件頁數： | 8/31頁 |
| 文件大小： | 0K |
| 描述： | IC CPLD 20NS LOWV LOW PWR 44TQFP |
| 標準包裝： | 160 |
| 系列： | ATF15xx |
| 可編程類型： | 系統內可編程（最少 10,000 次編程/擦除循環） |
| 最大延遲時間 tpd(1)： | 20.0ns |
| 電壓電源 - 內部： | 3 V ~ 3.6 V |
| 宏單元數： | 64 |
| 輸入/輸出數： | 32 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-TQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 608 (CN2011-ZH PDF) |
| 配用： | ATF15XX-DK3-ND - KIT DEV FOR ATF15XX CPLD'S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
16
ATF1504ASV(L)
1409J–PLD–6/05
JTAG-BST/ISP
Overview
The JTAG boundary-scan testing is controlled by the Test Access Port (TAP) controller
in the ATF1504ASV(L). The boundary-scan technique involves the inclusion of a shift-
register stage (contained in a boundary-scan cell) adjacent to each component so that
signals at component boundaries can be controlled and observed using scan testing
principles. Each input pin and I/O pin has its own boundary-scan cell (BSC) in order to
support boundary-scan testing. The ATF1504ASV(L) does not currently include a Test
Reset (TRST) input pin because the TAP controller is automatically reset at power-up.
The five JTAG modes supported include: SAMPLE/PRELOAD, EXTEST, BYPASS,
IDCODE and HIGHZ. The ATF1504ASV(L)’s ISP can be fully described using JTAG’s
BSDL as described in IEEE Standard 1149.1b. This allows ATF1504ASV(L) program-
ming to be described and implemented using any one of the third-party development
tools supporting this standard.
The ATF1504ASV(L) has the option of using four JTAG-standard I/O pins for boundary-
scan testing (BST) and in-system programming (ISP) purposes. The ATF1504ASV(L) is
programmable through the four JTAG pins using the IEEE standard JTAG programming
protocol established by IEEE Standard 1149.1 using 5V TTL-level programming signals
from the ISP interface for in-system programming. The JTAG feature is a programmable
option. If JTAG (BST or ISP) is not needed, then the four JTAG control pins are avail-
able as I/O pins.
JTAG Boundary-scan
Cell (BSC) Testing
The ATF1504ASV(L) contains up to 68 I/O pins and four input pins, depending on the
device type and package type selected. Each input pin and I/O pin has its own bound-
ary-scan cell (BSC) in order to support boundary-scan testing as described in detail by
IEEE Standard 1149.1. A typical BSC consists of three capture registers or scan regis-
ters and up to two update registers. There are two types of BSCs, one for input or I/O
pin, and one for the macrocells. The BSCs in the device are chained together through
the capture registers. Input to the capture register chain is fed in from the TDI pin while
the output is directed to the TDO pin. Capture registers are used to capture active
device data signals, to shift data in and out of the device and to load data into the update
registers. Control signals are generated internally by the JTAG TAP controller. The BSC
configuration for the input and I/O pins and macrocells are shown below.
BSC Configuration
for Input and I/O Pins
(Except JTAG TAP
Pins)
Note:
The ATF1504ASV(L) has pull-up option on TMS and TDI pins. This feature is selected as
a design option.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1422CS8#TRPBF | IC CONTROLLER HOT SWAP 8-SOIC |
| VI-B1J-CY-F2 | CONVERTER MOD DC/DC 36V 50W |
| ATF1504ASVL-20JU44 | IC CPLD 20NS LOWV LOW PWR 44PLCC |
| VI-B1J-CY-F1 | CONVERTER MOD DC/DC 36V 50W |
| ATF1508ASV-15JU84 | IC CPLD 15NS LOW V 84PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATF1504ASVL-20JC44 | 功能描述:CPLD - 復雜可編程邏輯器件 CPLD 64 MACROCELL w/ISP LOW PWR 3.3V RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| ATF1504ASVL-20JC68 | 功能描述:CPLD - 復雜可編程邏輯器件 CPLD 64 MACROCELL 3.3V 20NS IND TEMP RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| ATF1504ASVL-20JC84 | 功能描述:CPLD - 復雜可編程邏輯器件 CPLD 64 MACROCELL 3.3V 20NS IND TEMP RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| ATF1504ASVL-20JI44 | 功能描述:CPLD - 復雜可編程邏輯器件 CPLD 64 MACROCELL 3.3V 20NS IND TEMP RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
| ATF1504ASVL-20JI68 | 功能描述:CPLD - 復雜可編程邏輯器件 CPLD 64 MACROCELL 3.3V 20NS IND TEMP RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100 |
發布緊急采購，3分鐘左右您將得到回復。