- 您現在的位置：買賣IC網 > PDF目錄67389 > ATS612LSB PROXIMITY SENSOR-HALL EFFECT, 0.4-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | ATS612LSB |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| 封裝： | PLASTIC PACKAGE-4 |
| 文件頁數： | 4/17頁 |
| 文件大小： | 386K |
| 代理商： | ATS612LSB |
ATS612LSB
DYNAMIC, SELF-CALIBRATING, PEAK-DETECTING,
DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR
11
www.allegromicro.com
CRITERIA FOR DEVICE QUALIFICATION
All Allegro sensors are subjected to stringent qualification requirements prior to being released to production. To
become qualified, except for the destructive ESD tests, no failures are permitted.
Test Method and
Samples
Qualification Test
Test Conditions
Test Length
Per Lot
Comments
Temperature Humidity
JESD22-A101,
1000 hrs
77
Device biased for
Bias Life
TA = 85°C, RH = 85%
minimum power
Bias Life
JESD22-A108,
1000 hrs
77
TA = 150°C, TJ = 165°C
(Surge Operating Life)
JESD22-A108,
168 hrs
77
TA = 175°C, TJ = 190°C
Autoclave, Unbiased
JESD22-A102,
96 hrs
77
TA = 121°C, 15 psig
High-Temperature
JESD22-A103,
1000 hrs
77
(Bake) Storage Life
TA = 170°C
Temperature Cycle
JESD22-A104
1000 cycles
77
-55
°C to +150°C
ESD,
CDF-AEC-Q100-002
Pre/Post
3 per
Test to failure
Human Body Model
Reading
test
Pin 3 > 1.5 kV
All other pins > 3 kV
GEAR/TARGET SYSTEM EVALUATION*
An analog map of the magnetic signal can be
obtained by measuring the voltage at pin 3 (the capacitor
pin) while the device is running. The peak and valley hold
voltage will represent the peak-to-peak value of the signal.
More accurate measurements can be taken by connecting
an extremely small capacitor (0.05
F) from pin 3 to
ground. After the device is powered up and has switched
at least 64 times, a 1 k
bleed-off resistor should be
installed in parallel with the capacitor without powering
down the device. If the gear is then rotated at an ex-
tremely low speed, an analog representation of the gain-
adjusted signal can be measured at pin 3. Note that the
device should be re-powered at each air gap and the
above procedure repeated for accurate measurements. In
both cases, the analog signal may be compared to the
typical hysteresis of the device and device performance
can be estimated.
* In application, the terms “gear” and “target” are often
interchanged. However, “gear” is preferred when motion
is transferred.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS612LSG | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.25mm, 0.90%, 0.18-0.40V, THROUGH HOLE MOUNT |
| ATS616LSGTN-T | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.5mm, 200-400mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ATS625LSGTN-T | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 200-450mV, RECTANGULAR, THROUGH HOLE MOUNT |
| ATS630LSA | PROXIMITY SENSOR-HALL EFFECT, 0.3-2.5mm, 0.20-0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS631LSA | PROXIMITY SENSOR-HALL EFFECT, 0.3-2.5mm, 0.20-0.40V, ROUND, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS612LSB_1 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Dynamic, Self-Calibrating, Peak-Detecting, Differential Hall Effect Gear Tooth Sensor |
| ATS612LSG | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:DYNAMIC, SELF-CALIBRATING, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS-61300D-C1-R0 | 功能描述:散熱片 FANSINK ASSY 29.25X29.25X9.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61300K-C1-R0 | 功能描述:散熱片 FANSINK ASSY 29.25 X 29.25 X 14.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61300R-C1-R0 | 功能描述:散熱片 FANSINK ASSY 29.25 X 29.25 X 19.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
發布緊急采購，3分鐘左右您將得到回復。