參數資料
型號： ATTINY43U-SU
廠商： Atmel
文件頁數： 22/158頁
文件大小： 0K
描述： MCU AVR 4K FLASH 8MHZ 20-SOIC
產品培訓模塊： ATtiny43U Overview
MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 37
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 16
程序存儲器容量： 4KB（2K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 64 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
數據轉換器： A/D 4x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 管件
產品目錄頁面： 613 (CN2011-ZH PDF)
配用： ATSTK600-TINYX3U-ND - STK600 SOCKET/ADAPTER TINYX3U
118
8048C–AVR–02/12
ATtiny43U
The ADC contains a Sample and Hold circuit which ensures that the input voltage to the ADC is
held at a constant level during conversion.
The analog multiplexer allows eight single-ended channels to be connected to the ADC, includ-
ing the low four bits of port A, the internal temperature sensor, the internal voltage reference,
supply voltage (V
BAT) and ground (GND).
Internal reference voltage of nominally 1.1V is provided on-chip. Alternatively, V
CC can be used
as reference voltage.
16.3
ADC Operation
The ADC converts an analog input voltage to a 10-bit digital value through successive approxi-
mation. The minimum value represents GND and the maximum value represents the reference
voltage.The voltage reference for the ADC may be selected by writing to the REFS bit in
ADMUX. The VCC supply or an internal 1.1V voltage reference may be selected as the ADC
voltage reference.
The analog input channel is selected by writing to the MUX[2:0] bits in ADMUX. Any of the four
ADC input pins ADC[3:0], and V
BAT input pin can be selected as single ended input to the ADC.
The on-chip temperature sensor is selected by writing “111” to the MUX[2:0] bits in the ADMUX
register.
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSRA. Voltage reference and
input channel selections will not go into effect until ADEN is set. The ADC does not consume
power when ADEN is cleared, so it is recommended to switch off the ADC before entering power
saving sleep modes.
The ADC generates a 10-bit result which is presented in the ADC Data Registers, ADCH and
ADCL. By default, the result is presented right adjusted, but can optionally be presented left
adjusted by setting the ADLAR bit in ADCSRB.
If the result is left adjusted and no more than 8-bit precision is required, it is sufficient to read
ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content of the data
registers belongs to the same conversion. Once ADCL is read, ADC access to data registers is
blocked. This means that if ADCL has been read, and a conversion completes before ADCH is
read, neither register is updated and the result from the conversion is lost. When ADCH is read,
ADC access to the ADCH and ADCL Registers is re-enabled.
The ADC has its own interrupt which can be triggered when a conversion completes. When ADC
access to the data registers is prohibited between reading of ADCH and ADCL, the interrupt will
trigger even if the result is lost.
16.4
Starting a Conversion
Make sure the ADC is powered by clearing the ADC Power Reduction bit, PRADC, in the Power
A single conversion is started by writing a logical one to the ADC Start Conversion bit, ADSC.
This bit stays high as long as the conversion is in progress and will be cleared by hardware
when the conversion is completed. If a different data channel is selected while a conversion is in
progress, the ADC will finish the current conversion before performing the channel change.
Alternatively, a conversion can be triggered automatically by various sources. Auto Triggering is
enabled by setting the ADC Auto Trigger Enable bit, ADATE in ADCSRA. The trigger source is
selected by setting the ADC Trigger Select bits, ADTS in ADCSRB (see description of the ADTS
相關PDF資料
PDF描述
ATMEGA48-20PU IC AVR MCU 4K 20MHZ 5V 28DIP
308237951000200 COVER ASSMBLY FOR DIN CONN
ATMEGA48V-10PU IC AVR MCU 4K 10MHZ 1.8V 28DIP
ATSAM3N00AA-MU IC MCU 16KB CORTEX-M3 48-QFN
AT89LP428-20PU MCU 8051 4K FLASH SPI 28PDIP
相關代理商/技術參數
參數描述
ATTINY43U-SUR 功能描述:8位微控制器 -MCU 4KB FLSH 64B EE 256B SRAM-8MHz, IND 0.9V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ATTINY44-15MZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44-15SSZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY441-MMH 制造商:Atmel Corporation 功能描述:16MHZ, 3X3MM, 20 VQFN, IND. GRADE, GREEN - Bulk 制造商:Atmel Corporation 功能描述:IC MCU 8BIT 4KB FLASH 20VQFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*