CC, the device issues an internal reset with a time-out de" />
參數資料
型號： ATTINY43U-SU
廠商： Atmel
文件頁數： 79/158頁
文件大?。?/td> 0K
描述： MCU AVR 4K FLASH 8MHZ 20-SOIC
產品培訓模塊： ATtiny43U Overview
MCU Product Line Introduction
tinyAVR Introduction
標準包裝： 37
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 8MHz
連通性： USI
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 16
程序存儲器容量： 4KB（2K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 64 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
數據轉換器： A/D 4x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 管件
產品目錄頁面： 613 (CN2011-ZH PDF)
配用： ATSTK600-TINYX3U-ND - STK600 SOCKET/ADAPTER TINYX3U
27
8048C–AVR–02/12
ATtiny43U
To ensure sufficient V
CC, the device issues an internal reset with a time-out delay (tTOUT) after
the device reset is released by all other reset sources. The section “System Control and Reset”
on page 49 describes the start conditions for the internal reset. The delay (t
TOUT) is timed from
the Watchdog Oscillator and the number of cycles in the delay is set by the SUTn and CKSELn
fuse bits. The available delays are shown in Table 6-8.
Note:
The frequency of the Watchdog Oscillator is voltage and temperature dependent, as shown in Fig-
The main purpose of the delay is to keep the AVR in reset until V
CC has risen to a sufficient level.
The delay will not monitor the actual voltage and, hence, the user must make sure the delay time
is longer than the V
CC rise time. If this is not possible, an internal or external Brown-out Detec-
tion circuit should be used. A BOD circuit ensures there is sufficient V
CC before it releases the
reset line, and the time-out delay can then be disabled. It is not recommended to disable the
time-out delay without implementing a Brown-out Detection circuit.
The oscillator is required to oscillate for a minimum number of cycles before the clock is consid-
ered stable. An internal ripple counter monitors the oscillator output clock, and keeps the internal
reset active for a given number of clock cycles. The reset is then released and the device will
start to execute.
The start-up sequence for the clock includes both the time-out delay and the start-up time when
the device starts up from reset. When starting up from Power-down mode, V
CC is assumed to be
at a sufficient level and only the start-up time is included.
6.3
System Clock Prescaler
The ATtiny43U has a system clock prescaler, which means the system clock can be divided as
described in section “CLKPR – Clock Prescale Register” on page 28. This feature can be used
to lower system clock frequency and decrease the power consumption at times when require-
ments for processing power is low. This can be used with all clock source options, and it will
affect the clock frequency of the CPU and all synchronous peripherals. Clock signals clk
I/O,
clk
ADC, clkCPU, and clkFLASH are divided by a factor as shown in Table 20-4 on page 161.
6.3.1
Switching Time
When changing prescaler settings, the System Clock Prescaler ensures that no glitches occurs
in the clock system. It also ensures that no intermediate frequency is higher than either the clock
frequency corresponding to the previous setting or the clock frequency corresponding to the new
setting. The ripple counter of the prescaler runs at the same frequency as the undivided clock,
which may be higher than the CPU's clock frequency. Hence, even if it was readable, it is not
possible to determine the state of the prescaler, and it is not possible to predict the exact time it
takes to switch from one clock division to the other. From the time the CLKPS values are written,
it takes between T1 + T2 and T1 + 2 * T2 before the new clock frequency is active. In this inter-
val, two active clock edges are produced. Here, T1 is the previous clock period, and T2 is the
period corresponding to the new prescaler setting.
Table 6-8.
Number of Watchdog Oscillator Cycles
Typ Time-out (V
CC = 5.0V)
Typ Time-out (V
CC = 3.0V)
Number of Cycles
0 ms
0
4.1 ms
4.3 ms
512
65 ms
69 ms
8K (8,192)
相關PDF資料
PDF描述
ATMEGA48-20PU IC AVR MCU 4K 20MHZ 5V 28DIP
308237951000200 COVER ASSMBLY FOR DIN CONN
ATMEGA48V-10PU IC AVR MCU 4K 10MHZ 1.8V 28DIP
ATSAM3N00AA-MU IC MCU 16KB CORTEX-M3 48-QFN
AT89LP428-20PU MCU 8051 4K FLASH SPI 28PDIP
相關代理商/技術參數
參數描述
ATTINY43U-SUR 功能描述:8位微控制器 -MCU 4KB FLSH 64B EE 256B SRAM-8MHz, IND 0.9V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ATTINY44-15MZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY44-15SSZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY441-MMH 制造商:Atmel Corporation 功能描述:16MHZ, 3X3MM, 20 VQFN, IND. GRADE, GREEN - Bulk 制造商:Atmel Corporation 功能描述:IC MCU 8BIT 4KB FLASH 20VQFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*