參數資料
型號: AX88178
廠商: Electronic Theatre Controls, Inc.
英文描述: USB to 10/100/1000 Gigabit Ethernet/HomePNA Controller
中文描述: USB接口10/100/1000千兆以太網/電話線網絡控制器
文件頁數: 8/35頁
文件大?。?/td> 218K
代理商: AX88178
ASIX ELECTRONICS CORPORATION
8
AX88178 L
USB to 10/100/1000 Gigabit Ethernet/HomePNA Controller
3.0 Function Description
3.1 USB Core and Interface
The USB core and interface contains an USB 2.0 transceiver, serial interface engine (SIE), USB bus protocol
handshaking block, USB standard command, vendor command registers, logic for supporting bulk transfer, and interrupt
transfer, etc. The USB interface is used to communicate with USB host controller and is compliant with USB
specification V1.0, V1.1 and V2.0.
3.2 Gigabit MAC Core
The gigabit MAC core supports IEEE 802.3, 802.3u, and 802.3ab MAC sub-layer functions, such as basic MAC frame
receive and transmit, CRC checking and generation, filtering, forwarding, flow-control in full-duplex mode, and
collision-detection and handling in half-duplex mode, etc. It provides gigabit media-independent (GMII) and reduced
gigabit media-independent (RGMII) interface for interfacing with Gigabit Ethernet PHY.
3.3 Station Management (STA)
The station management interface provides a simple, two-wire, serial interface to connect to a managed PHY device for
the purposes of controlling the PHY and gathering status from the PHY. The station management interface allows
communicating with multiple PHY devices at the same time by identifying the managed PHY with 5-bit, unique Phy ID.
3.4 Memory Arbiter
The memory arbiter block is responsible for storing received MAC frames into on-chip SRAM (packet buffer) and then
forwarding to USB bus upon request from USB host via bulk in transfer. It also monitors packet buffer usage in
full-duplex mode for triggering PAUSE frame transmission out on TX direction. The memory arbiter block is also
responsible for storing MAC frames received from USB host via bulk out transfer and waiting to be transmitted out
towards Ethernet network.
3.5 USB to Ethernet Bridge
The USB to Ethernet bridge block is responsible for converting Ethernet MAC frame into USB packets or vice-versa.
This block supports proprietary burst transfer mechanism (submitted for US patent application) to offload software
burden and to offer very high packet transfer throughput over USB bus.
3.6 Serial EEPROM Loader
The serial EEPROM loader is responsible for reading configuration data automatically from external serial EEPROM
after power-on reset.
3.7 General Purpose I/O
There are 3 general purpose I/O pins provided by this ASIC.
相關PDF資料
PDF描述
AX88178L USB to 10/100/1000 Gigabit Ethernet/HomePNA Controller
AY-5-8116 DUAL BAUD RATE GENERATOR
AY-5-8116T DUAL BAUD RATE GENERATOR
AY-5-8136 DUAL BAUD RATE GENERATOR
AY-5-8136T DUAL BAUD RATE GENERATOR
相關代理商/技術參數
參數描述
AX88178A 制造商:ASIX 制造商全稱:ASIX 功能描述:AX88179 -- USB3.0 轉 10/100/1000M 千兆以太網控制芯片
AX88178L 制造商:ASIX 制造商全稱:ASIX 功能描述:USB to 10/100/1000 Gigabit Ethernet/HomePNA Controller
AX88179 制造商:ASIX 制造商全稱:ASIX 功能描述:AX88179 -- USB3.0 轉 10/100/1000M 千兆以太網控制芯片
AX88179QF 制造商:ASIX Electronics Corporation 功能描述:
AX88180 制造商:ASIX 制造商全稱:ASIX 功能描述:High-Performance Non-PCI 32-bit 10/100/1000M Gigabit Ethernet Controller