- 您現在的位置：買賣IC網 > PDF目錄223454 > BD6231F-E2F8 BRUSH DC MOTOR CONTROLLER, 1 A, PDSO8 PDF資料下載
參數資料
| 型號： | BD6231F-E2F8 |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO8 |
| 封裝： | ROHS COMPLIANT, SOP-8 |
| 文件頁數： | 2/17頁 |
| 文件大?。?/td> | 383K |
| 代理商： | BD6231F-E2F8 |
Technical Note
10/16
BD6230, BD6231, BD6232, BD6235, BD6236, BD6237
www.rohm.com
2009.08 - Rev.C
○
c
2009 ROHM Co., Ltd. All rights reserved.
e) f) PWM control mode A
The rotational speed of the motor can be controlled by the switching duty when the PWM signal is input to the FIN
pin or the RIN pin. In this mode, the high side output is fixed and the low side output does the switching,
corresponding to the input signal. The switching operates by the output state toggling between "L" and "Hi-Z".
The PWM frequency can be input in the range between 20kHz and 100kHz. Note that control may not be attained
by switching on duty at frequencies lower than 20kHz, since the operation functions via the stand-by mode. Also,
circuit operation may not respond correctly when the input signal is higher than 100kHz. To operate in this mode,
connect the VREF pin with VCC pin. In addition, establish a current path for the recovery current from the motor, by
connecting a bypass capacitor (10F or more is recommended) between VCC and ground.
Control input : H
Control input : L
Fig.38 PWM control mode A operation (output stage)
Fig.39 PWM control mode A operation (timing chart)
g) h) PWM control mode B
The rotational speed of the motor can be controlled by the switching duty when the PWM signal is input to the FIN
pin or the RIN pin. In this mode, the low side output is fixed and the high side output does the switching,
corresponding to the input signal. The switching operates by the output state toggling between "L" and "H".
The PWM frequency can be input in the range between 20kHz and 100kHz. Also, circuit operation may not respond
correctly when the input signal is higher than 100kHz. To operate in this mode, connect the VREF pin with VCC pin.
In addition, establish a current path for the recovery current from the motor, by connecting a bypass capacitor (10F
or more is recommended) between VCC and ground.
Control input : H
Control input : L
Fig.40 PWM control mode B operation (output stage)
Fig.41 PWM control mode B operation (timing chart)
M
ON
OFF
ON
M
ON
OFF
FIN
RIN
OUT1
OUT2
M
OFF
ON
OFF
ON
M
ON
OFF
ON
FIN
RIN
OUT1
OUT2
相關PDF資料 |
PDF描述 |
|---|---|
| BD826 | 1 A, 45 V, PNP, Si, POWER TRANSISTOR, TO-202 |
| BDV64 | 12 A, 60 V, PNP, Si, POWER TRANSISTOR, TO-218 |
| BF-4000622 | 24 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| BF-4001222 | 48 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| BF-4002422 | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD6231HFP | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-bridge driver for DC brush motor |
| BD6231HFP-TR | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE 36V max 1 Chan 1.0A 1.5ohm RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| BD6232 | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD62321HFP | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-bridge driver |
| BD62321HFP-TR | 功能描述:IC H-BRIDGE DVR 36V 1CH 3A HRP7 RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
發布緊急采購，3分鐘左右您將得到回復。