- 您現在的位置：買賣IC網 > PDF目錄295161 > BQ20Z80DBT-V101 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO38 PDF資料下載
參數資料
| 型號： | BQ20Z80DBT-V101 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO38 |
| 封裝： | GREEN, PLASTIC, TSSOP-38 |
| 文件頁數： | 6/73頁 |
| 文件大?。?/td> | 1094K |
| 代理商： | BQ20Z80DBT-V101 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
www.ti.com
Charge and Discharge Overcurrent
bq20z80-V101
SLUS625D – SEPTEMBER 2004 – REVISED OCTOBER 2005
For the bq20z80 to fully recover from a pack undervoltage condition, SBS.Voltage( ) should be
≥ DF:PUV
Recovery threshold. When this occurs, the discharge FET is allowed to be turned on only if other safety and
configuration states permit. On recovery from a pack undervoltage condition, SBS.BatteryStatus( ) [TDA] is reset,
SBS.ChargingCurrent( ) and SBS.ChargingVoltage( ) are set to the appropriate value per the charging algorithm
and SBS.OperationStatus( ) [XDSG] and SBS.SafetyStatus( ) [PUV] are reset.
However, when SBS.SafetyStatus(
) [PUV] is set, the discharge FET is turned on again, as long as
SBS.Current( ) is reported to be
≥ DF:Chg Current Threshold. No other flags change state until full recovery is
reached. This prevents overheating the discharge-FET body diode during charging from an undervoltage
condition.
SIZE
DEFAULT
NAME
DESCRIPTION
FORMAT
VALID RANGE
UNITS
(BYTES)
VALUE
PUV Threshold
0 to 16000
2
11000
mV
PUV Recovery
1st Level Safety / Voltage (0)
Integer
0 to 16000
2
12000
PUV TIme
0 to 60
1
s
2
The bq20z80 has two independent tiers (levels) of overcurrent protection for discharge and charge. These two
tiers require the SBS.Current( ) to be
≥ a programmed threshold in either charge or discharge current for a
period
≥ a programmable time. If the programmable time for any of the current-protection levels is set to 0, that
specific feature is disabled.
The bq29312A provides a third level of discharge overcurrent (overload) protection that reacts according to the
bq29312A internal settings. The bq29312A discharge overcurrent is configured by the bq20z80, where DF:AFE
OC Dsg (see bq29312A OLV register) and DF:AFE OC Dsg Time (see bq29312A OLT register) are used to
provide the current threshold and delay timing. See the 'Overload Detection' section of the bq29312A data sheet
for more details and the appropriate values to use.
For the first two tiers of overcurrent protection, during the period between when excessive current is detected
and the expiration of the timer, the respective SBS.SafetyAlert( ) bit is set. If the timer expires, or SBS.Current( )
returns within normal operating parameters, the SBS.SafetyAlert( ) bit is cleared.
SBS.SAFETYALERT( ),
DF CLEAR
DF THRESHOLD
DF TIME
FET
SBS.SAFETYSTATUS( )
THRESHOLD
AND DF:Nonremovable Cfg
Tier-1
OC (1st Tier) Chg
OC (1st Tier) Chg Time
CHG
OCC
Charge
OC Chg Recovery
Tier-2
OC (2nd Tier) Chg
OC (2nd Tier) Chg Time
CHG
OCC2
Charge
Tier-1
OC (1st Tier) Dsg
OC (1st Tier) Dsg Time
DSG
OCD
Discharge
OC Dsg Recovery
Tier-2
OC (2nd Tier) Dsg
OC (2nd Tier) Dsg Time
DSG
OCD2
Discharge
Tier-3
CHG,
AFE OC Dsg
AFE OC Dsg Time
AOCD(1)
AFE OC DsgRecovery
Discharge
DSG
(1)
No SBS.SafetyAlert( ) flag
If the timer of any tier expires during charging, the charge FET is turned off and the ZVCHG FET is turned off if
the DF:Operation Cfg A [ZVCHG1, ZVCHG0] are set appropriately. When this occurs, the internal
AFE_Current_Fault timer is started from 0, SBS.ChargingCurrent( ) and SBS.ChargingVoltage( ) are set to 0,
SBS.BatteryStatus( ) [TCA] is set, and the appropriate tier flag is set in SBS.SafetyStatus( ).
However, when the bq20z80 has either of SBS.SafetyStatus( ) [OCC, OCC2] set, the charge FET is turned on
again, as long as SBS.Current( ) is reported to be
≤ (-) DF:Dsg Current Threshold. No other flags change state
until full recovery is reached. This prevents overheating the charge-FET body diode during discharge. This action
is not affected by the state of DF:Operation Cfg B [NR].
14
相關PDF資料 |
PDF描述 |
|---|---|
| BQ2110LB-001 | DC-DC REG PWR SUPPLY MODULE |
| BQ24630RGET | SWITCHED CAPACITOR CONVERTER, PQCC24 |
| BQ25070DQCR | 1 A BATTERY CHARGE CONTROLLER, PDSO10 |
| BQ3285ESSNTR | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
| BQ3285ESS-N | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ20Z80DBT-V101G4 | 功能描述:電池管理 1% acc Gas Gauge for LiIon batterie RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V102 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V110 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80DBT-V110G4 | 功能描述:電池管理 SBS 1.1-Compliant Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ20Z80EVM-001 | 功能描述:電源管理IC開發工具 Impedance Track Fuel Gge LiIon Batt Packs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。