- 您現在的位置：買賣IC網 > PDF目錄166633 > BU4815F-TR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 PDF資料下載
參數資料
| 型號： | BU4815F-TR |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| 封裝： | ROHS COMPLIANT, SOP-4 |
| 文件頁數： | 7/9頁 |
| 文件大小： | 277K |
| 代理商： | BU4815F-TR |
Technical Note
7/8
BU48□□G Series, BU48□□F Series, BU48□□FVE Series,
BU49□□G Series, BU49□□F Series, BU49□□FVE Series
www.rohm.com
2011.03 - Rev.D
2011 ROHM Co., Ltd. All rights reserved.
●
Notes for use
1.
Absolute maximum range
Absolute Maximum Ratings are those values beyond which the life of a device may be destroyed. We cannot be
defined the failure mode, such as short mode or open mode. Therefore a physical security countermeasure, like fuse,
is to be given when a specific mode to be beyond absolute maximum ratings is considered.
2.
GND potential
GND terminal should be a lowest voltage potential every state.
Please make sure all pins that are over ground even if include transient feature.
3
Electrical Characteristics
Be sure to check the electrical characteristics that are one the tentative specification will be changed by temperature,
supply voltage, and external circuit.
4.
Bypass Capacitor for Noise Rejection
Please put into the to reject noise between VDD pin and GND with 1uF over and between VOUT pin and GND with
1000pF. If extremely big capacitor is used, transient response might be late. Please confirm sufficiently for the point.
5.
Short Circuit between Terminal and Soldering
Don’t short-circuit between Output pin and VDD pin, Output pin and GND pin, or VDD pin and GND pin. When soldering
the IC on circuit board please is unusually cautious about the orientation and the position of the IC. When the
orientation is mistaken the IC may be destroyed.
6.
Electromagnetic Field
Mal-function may happen when the device is used in the strong electromagnetic field.
7.
The Vdd line inpedance might cause oscillation because of the detection current.
8.
A Vdd -GND capacitor (as close connection as possible) should be used in high Vdd line impedance condition.
9.
Lower than the mininum input voltage makes the Vout high impedance, and it must be Vdd in pull up (Vdd) condition.
10. Recommended value of RL Resistar is over 10k (VDET=1.5V~4.8V),
over 100k (VDET=0.9~1.4V).
11.
This IC has extremely high impedance terminals. Small leak current due to the uncleanness of PCB surface might
cause unexpected operations. Application values in these conditions should be selected carefully. If 10M leakage is
assumed between the CT terminal and the GND terminal, 1M connection between the CT terminal and the Vdd
terminal would be recommended. Also, if the leakage is assumed between the Vout terminal and the GND terminal, the
pull up resistor should be less than 1/10 of the assumed leak resistance.
12. External parameters
For Rl, the recommended range is 10k~1M. There are many factors (board layout, etc) that can affect
characteristics. Please verify and confirm using practical applications.
13. Power on reset operation
Please note that the power on reset output varies with the Vcc rise up time. Please verify the actual operation.
14. Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC. Therefore, be
certain to use proper discharge procedure before each process of the test operation.To prevent electrostatic
accumulation and discharge in the assembly process, thoroughly ground yourself and any equipment that could sustain
ESD damage, and continue observing ESD-prevention procedures in all handing, transfer and storage operations.
Before attempting to connect components to the test setup, make certain that the power supply is OFF. Likewise, be
sure the power supply is OFF before removing any component connected to the test setup.
15. When the power supply, is turned on because of incertain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
相關PDF資料 |
PDF描述 |
|---|---|
| BU4S66-TL | 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO5 |
| BUD725D-SMD | TRANSISTOR | BJT | NPN | 400V V(BR)CEO | 5A I(C) | TO-251AA |
| BUD7312 | TRANSISTOR | BJT | NPN | 600V V(BR)CEO | 3A I(C) | TO-251AA |
| BUD7312SMD | TRANSISTOR | BJT | NPN | 600V V(BR)CEO | 3A I(C) | TO-252AA |
| BUD742 | TRANSISTOR | BJT | NPN | 400V V(BR)CEO | 5A I(C) | TO-251AA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU4815FVE | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Voltage Detector IC |
| BU4815FVE-TR | 制造商:ROHM Semiconductor 功能描述:IC, CMOS VOLTAGE DETECTOR - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC VOLT DETECTOR STD 5-VSOF |
| BU4815G | 制造商:ROHM 制造商全稱:Rohm 功能描述:Low Voltage Detector IC |
| BU4815GTR | 制造商:ROHM Semiconductor 功能描述: |
| BU4815G-TR | 功能描述:電壓監測器/監控器 CMOS Voltage Detector;1.5V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。