- 您現在的位置：買賣IC網 > PDF目錄223464 > BU7346GUL 38 MHz, OTHER CLOCK GENERATOR, PBGA6 PDF資料下載
參數資料
| 型號： | BU7346GUL |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 38 MHz, OTHER CLOCK GENERATOR, PBGA6 |
| 文件頁數： | 4/5頁 |
| 文件大?。?/td> | 130K |
| 代理商： | BU7346GUL |
4/4
REV. A
●Cautions on use（common）
（１）Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down
devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit. If any special mode exceeding the
absolute maximum ratings is assumed, consideration should be given to take physical safety measures including the use of fuses, etc.
（２）Operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The electrical
characteristics are guaranteed under the conditions of each parameter.
（３）Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown due to the
reverse connection, such as mounting an external diode between the power supply and the IC’s power supply terminal.
（４）Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines.In this regard, for the digital
block power supply and the analog block power supply, even though these power supplies has the same level of potential, separate the
power supply pattern for the digital block from that for the analog block, thus suppressing the diffraction of digital noises to the analog
block power supply resulting from impedance common to the wiring patterns. For the GND line, give consideration to design the
patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At the same
time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be used present no
problem including the occurrence of capacity dropout at a low temperature, thus determining the constant.
（５）GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state. Furthermore,
check to be sure no terminals are at a potential lower than the GND voltage including an actual electric transient.
（６）Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can break down
the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between the terminal and the power
supply or the GND terminal, the ICs can break down.
（７）Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
（８）Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress. Therefore, be
sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set PCB to/from the jig for the
inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig. After the completion of the inspection,
be sure to turn OFF the power supply and then dismount it from the jig. In addition, for protection against static electricity, establish a
ground for the assembly process and pay thorough attention to the transportation and the storage of the set PCB.
（９）Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the parasitic element
can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the input terminal. Therefore, pay
thorough attention not to handle the input terminals, such as to apply to the input terminals a voltage lower than the GND respectively,
so that any parasitic element will operate. Furthermore, do not apply a voltage to the input terminals when no power supply voltage is
applied to the IC. In addition, even if the power supply voltage is applied, apply to the input terminals a voltage lower than the power
supply voltage or within the guaranteed value of electrical characteristics.
（１０）Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern from the
small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the wiring pattern
and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay attention not to cause
fluctuations in the GND wiring pattern of external parts as well.
（１１）External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a degradation
in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc.
相關PDF資料 |
PDF描述 |
|---|---|
| BUF01900AIDRCR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| BUF08821AIPWPR | VIDEO CLOCK GENERATOR, PDSO20 |
| BUK657-600B | N-Channel Enhancement MOSFET |
| BUK657-600C | N-Channel Enhancement MOSFET |
| BUK7105-40ATE | TrenchPLUS standard level FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU-74-0 | 功能描述:測試電夾 BLACK INSULATOR RoHS:否 制造商:Pomona Electronics 類型:Minigrabber clip 顏色:Black |
| BU7411G | 制造商:ROHM 制造商全稱:Rohm 功能描述:SILICON MONOLITHIC INTEGRATED CIRCUIT |
| BU7411G-TR | 功能描述:IC OP AMP ULP GROUND SENSE 5SSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 特色產品:CMOS Operational Amplifier 標準包裝:2,500 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:1000µV 電流 - 電源:900µA 電流 - 輸出 / 通道:1mA 電壓 - 電源，單路/雙路(±):5 V ~ 14.5 V，±2.5 V ~ 7.25 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-SOP 包裝:帶卷 (TR) 產品目錄頁面:1372 (CN2011-ZH PDF) 其它名稱:BD7562SF-E2TR |
| BU7411SG | 制造商:ROHM 制造商全稱:Rohm 功能描述:SILICON MONOLITHIC INTEGRATED CIRCUIT |
| BU7411SG-TR | 功能描述:運算放大器 - 運放 OP Amp Sgl GP 5.5V RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。