- 您現在的位置：買賣IC網 > PDF目錄8580 > BUF20820AIDCPR (Texas Instruments)IC 18CH PROG V-REF GEN 38-HTSSOP PDF資料下載
參數資料
| 型號： | BUF20820AIDCPR |
| 廠商： | Texas Instruments |
| 文件頁數： | 2/29頁 |
| 文件大小： | 0K |
| 描述： | IC 18CH PROG V-REF GEN 38-HTSSOP |
| 標準包裝： | 1 |
| 應用： | TFT-LCD 面板：伽瑪緩沖器，VCOM 驅動器 |
| 輸出類型： | 滿擺幅 |
| 電路數： | 18 |
| 電流 - 電源： | 18mA |
| 電流 - 輸出 / 通道： | 100mA |
| 電壓 - 電源，單路/雙路(±)： | 7 V ~ 18 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-TFSOP （0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 38-HTSSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | 296-19400-6 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
BUF20820
SBOS330E DECEMBER 2005 REVISED OCTOBER 2008
www.ti.com
10
addressed register, the master continues to send data for
the next register. The BUF20820 automatically and
sequentially steps through subsequent registers as
additional data is sent. The process continues until all
desired registers have been updated or a STOP condition
is sent.
To write to multiple DAC registers:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send either the DAC_1 address byte to start at the first
DAC, or send the address byte for whichever DAC will
be the first in the sequence of DACs to be updated.
The BUF20820 will begin with this DAC and step
through subsequent DACs in sequential order.
4.
Send the bytes of data; begin by sending the most
significant byte (bits D15D8, of which only bits D9
and D8 have meaning, and bits D15D14 must not be
01), followed by the least significant byte (bits D7D0).
The first two bytes are for the DAC addressed in step
3 above. Its register is automatically updated after
receiving the second byte. The next two bytes are for
the following DAC. That DAC register is updated after
receiving the fourth byte. This process continues until
the registers of all following DACs have been updated.
The last address, 10100, is the address of the write
disable bit and cannot be accessed using this method.
It must be written using the write to a single DAC
register procedure.
5.
Send a STOP condition on the bus.
The BUF20820 will acknowledge each byte. To terminate
communication, send a STOP or START condition on the
bus. Only DAC registers that have received both bytes of
data will be updated.
Reading:
Reading a DAC register will return the data stored in the
DAC. This data can differ from the data stored in the DAC
register. See the Output Latch section.
To read the DAC value:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send the DAC address byte. Bits D7D5 must be set
to 0; Bits D4D0 are the DAC address. Only DAC
addresses 00000 to 10100 are valid and will be
acknowledged. For address 10100, only D0 has
meaning. This bit is the write disable bit.
4.
Send a START or STOP/START condition on the bus.
5.
Send
correct
device
address
and
read/write
bit = HIGH. The BUF20820 will acknowledge this
byte.
6.
Receive two bytes of data. They are for the specified
DAC. The first received byte is the most significant
byte (bits D15D8, only bits D9 and D8 have
meaning); the next byte is the least significant byte
(bits D7D0).
7.
Acknowledge after receiving the first byte.
8.
Do not acknowledge the second byte to end the read
transaction.
Communication may be terminated by sending a
premature STOP or START condition on the bus, or by not
sending the acknowledge.
To Read Multiple DACs:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send either the DAC_1 address byte to start at the first
DAC, or send the address byte for whichever DAC will
be the first in the sequence of DACs to be read. The
BUF20820 will begin with this DAC and step through
subsequent DACs in sequential order.
4.
Send a START or STOP/START condition on the bus.
5.
Send
correct
device
address
and
read/write
bit = HIGH. The BUF20820 will acknowledge this
byte.
6.
Receive two bytes of data. They are for the specified
DAC. The first received byte is the most significant
byte (bits D15D8, only bits D9 and D8 have
meaning), the next byte is the least significant byte
(bits D7D0).
7.
Acknowledge after receiving each byte of data except
for the last byte. The acknowledge bit of the last byte
should be HIGH to end the read operation.
8.
When all desired DACs have been read, send a STOP
or START condition on the bus.
Communication may be terminated by sending a
premature STOP or START condition on the bus, or by not
sending the acknowledge.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5544BCPZ-RL7 | IC DAC 16BIT SER QUAD 32-LFCSP |
| AD7245AQ | IC DAC 12BIT W/REF 24-CDIP |
| AD7225LPZ-REEL | IC DAC 8BIT QUAD W/AMP 28-PLCC |
| AD558KP | IC DAC 8BIT 5-15V IN MONO 20PLCC |
| VI-2WW-IV-F2 | CONVERTER MOD DC/DC 5.5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BUF20820AIDCPRE4 | 功能描述:LCD Gamma緩沖器 18-Ch Vltg Generator w/2 Prog VCOM Chs RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF20820EVM | 功能描述:放大器 IC 開發工具 BUF20800-BUF20820 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| BUF22821 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory |
| BUF22821AIDCPR | 功能描述:LCD Gamma緩沖器 Prgrmbl Gam-Vltg Gen & Vcom Calibrator RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF22821EVM | 功能描述:放大器 IC 開發工具 BUF22821EVM Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。