參數資料
型號： C8051F000
廠商： Silicon Laboratories Inc
文件頁數： 21/171頁
文件大?。?/td> 0K
描述： IC 8051 MCU 32K FLASH 64TQFP
標準包裝： 160
系列： C8051F00x
核心處理器： 8051
芯體尺寸： 8-位
速度： 20MHz
連通性： SMBus（2 線/I²C），SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，溫度傳感器，WDT
輸入/輸出數： 32
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 8x12b，D/A 2x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 托盤
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
16.6.1. Control Register
The SMBus Control register SMB0CN is used to configure and control the SMBus interface. All of the bits in the
register can be read or written by software. Two of the control bits are also affected by the SMBus hardware. The
Serial Interrupt flag (SI, SMB0CN.3) is set to logic 1 by the hardware when a valid serial interrupt condition occurs.
It can only be cleared by software. The Stop flag (STO, SMB0CN.4) is cleared to logic 0 by hardware when a
STOP condition is present on the bus.
Setting the ENSMB flag to logic 1 enables the SMBus interface. Clearing the ENSMB flag to logic 0 disables the
SMBus interface and removes it from the bus. Momentarily clearing the ENSMB flag and then resetting it to logic
1 will reset a SMBus communication. However, ENSMB should not be used to temporarily remove a device from
the bus since the bus state information will be lost. Instead, the Assert Acknowledge (AA) flag should be used to
temporarily remove the device from the bus (see description of AA flag below).
Setting the Start flag (STA, SMB0CN.5) to logic 1 will put the SMBus in a master mode. If the bus is free, the
SMBus hardware will generate a START condition. If the bus is not free, the SMBus hardware waits for a STOP
condition to free the bus and then generates a START condition after a 5
s delay per the SMB0CR value. (In
accordance with the SMBus protocol, the SMBus interface also considers the bus free if the bus is idle for 50
s and
no STOP condition was recognized.) If STA is set to logic 1 while the SMBus is in master mode and one or more
bytes have been transferred, a repeated START condition will be generated. To ensure proper operation, the STO
flag should be explicitly cleared before setting STA to a logic 1.
When the Stop flag (STO, SMB0CN.4) is set to logic 1 while the SMBus interface is in master mode, the hardware
generates a STOP condition on the SMBus. In a slave mode, the STO flag may be used to recover from an error
condition. In this case, a STOP condition is not generated on the SMBus, but the SMBus hardware behaves as if a
STOP condition has been received and enters the “not addressed” slave receiver mode. The SMBus hardware
automatically clears the STO flag to logic 0 when a STOP condition is detected on the bus.
The Serial Interrupt flag (SI, SMB0CN.3) is set to logic 1 by hardware when the SMBus interface enters one of 27
possible states. If interrupts are enabled for the SMBus interface, an interrupt request is generated when the SI flag
is set. The SI flag must be cleared by software. While SI is set to logic 1, the clock-low period of the serial clock
will be stretched and the serial transfer is suspended.
The Assert Acknowledge flag (AA, SMB0CN.2) is used to set the level of the SDA line during the acknowledge
clock cycle on the SCL line. Setting the AA flag to logic 1 will cause an ACKNOWLEDGE (low level on SDA) to
be sent during the acknowledge cycle if the device has been addressed. Setting the AA flag to logic 0 will cause a
NOT ACKNOWLEDGE (high level on SDA) to be sent during acknowledge cycle. After the transmission of a
byte in slave mode, the slave can be temporarily removed from the bus by clearing the AA flag. The slave’s own
address and general call address will be ignored. To resume operation on the bus, the AA flag must be reset to logic
1 to allow the slave’s address to be recognized.
Setting the SMBus Free Timer Enable bit (FTE, SMB0CN.1) to logic 1 enables the SMBus Free Timeout feature. If
SCL and SDA remain high for the SMBus Free Timeout given in the SMBus Clock Rate Register (Figure 16.5), the
bus will be considered free and a Start will be generated if pending. The bus free period should be greater than
50
s.
Setting the SMBus timeout enable bit (TOE, SMB0CN.0) to logic 1 enables Timer 3 to count up when the SCL line
is low and Timer 3 is enabled. If Timer 3 overflows, a Timer 3 interrupt will be generated, which will alert the CPU
that a SMBus SCL low timeout has occurred.
117
Rev. 1.7
相關PDF資料
PDF描述
PIC18F6627-I/PT IC PIC MCU FLASH 48KX16 64TQFP
PIC32MX775F512H-80V/MR IC MCU 32BIT 512KB FLASH 64QFN
PIC18F2685-I/SP IC PIC MCU FLASH 48KX16 28-DIP
PIC18LF4682-I/PT IC PIC MCU FLASH 40KX16 44TQFP
PIC32MX775F256L-80I/PF IC MCU 32BIT 256K FLASH 100TQFP
相關代理商/技術參數
參數描述
C8051F000_03 制造商:SILABS 制造商全稱:SILABS 功能描述:Mixed-Signal 32KB ISP FLASH MCU Family
C8051F000-GQ 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F000-GQR 功能描述:8位微控制器 -MCU 32KB 12ADC 64Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F000R 功能描述:8位微控制器 -MCU C 12Bit 64Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F000TB 功能描述:開發板和工具包 - 8051 USE 634-C8051F005TB RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*