- 您現在的位置：買賣IC網 > PDF目錄366673 > CAT1161PI-42TE13 Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer PDF資料下載
參數資料
| 型號： | CAT1161PI-42TE13 |
| 英文描述： | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| 中文描述： | 監控電路，帶有I2C串行CMOS EEPROM的，精密復位控制器和看門狗定時器 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 69K |
| 代理商： | CAT1161PI-42TE13 |
7
CAT1161/2
Doc No. 3002, Rev. D
FUNCTIONAL DESCRIPTION
The CAT1161/2 supports the I
2
C Bus data transmission
protocol. This Inter-Integrated Circuit Bus protocol defines
any device that sends data to the bus to be a transmitter
and any device receiving data to be a receiver. The
transfer is controlled by the Master device which
generates the serial clock and all START and STOP
conditions for bus access. Both the Master device and
Slave device can operate as either transmitter or receiver,
but the Master device controls which mode is activated.
I
2
C Bus Protocol
The features of the I
2
C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT1161/2 monitors the
SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant
bits of the 8-bit slave address are fixed as 1010.
The next three bits (Figure 6) define memory addressing.
For the CAT1161/162 the three bits define higher order
bits.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this bit
is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT1161/2 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT1161/2 then performs a Read or Write operation
depending on the R/
W
bit.
ACKNOWLEDGE
1
START
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
Figure 5. Acknowledge Timing
1
0
1
0
a10
a9
a8
R/W
Figure 6. Slave Address Bits
**a8, a9 and a10 correspond to the address of the memory array address word.
CAT1161/2
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1162 | Miniature, 1W Isolated Regulated DC/DC Converters 10-PDIP |
| CAT1162PI-30TE13 | Miniature, 1W Isolated Regulated DC/DC Converters 12-SOP |
| CAT1162PI-42TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161P-30TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161P-42TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1161PI-45 | 功能描述:監控電路 16K I2C Memory w/WDT RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1161W28 | 制造商:ON Semiconductor 功能描述: |
| CAT1161W-28 | 制造商:ON Semiconductor 功能描述:SUPERVISORY CCT 16K E2 SMD 1161 |
| CAT1161W-28 | 制造商:ON Semiconductor 功能描述:IC SM SUPERVISORY CCT W/ 16K E2 |
| CAT1161W-30 | 制造商:ON Semiconductor 功能描述:SUPERVISORY CCT 16K E2 SMD 1161 |
發布緊急采購，3分鐘左右您將得到回復。